Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2015.06–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  P2759  Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)  


DESCRIPTION

The amount of current flow to the shift solenoid valve SLU is controlled by the TCM. During the lock-up operation, if the current increases, the lock-up hydraulic pressure increases.

C221407E01
4.729,2.135 5.031,1.188 5.031,1.188 5.094,1.188 true 4.969,2.323 5.125,2.688 5.125,2.688 5.188,2.688 true 5.76,2.396 5.917,2.688 5.917,2.688 5.979,2.688 true 6.031,2.594 6.917,2.813 0.885,0.219 10 false Solenoid Coil 0.135,0.688 1.385,0.906 1.25,0.219 10 false Hydraulic Pressure 2.573,3.01 3.135,3.229 0.563,0.219 10 false Current 5.24,2.615 5.771,2.833 0.531,0.219 10 false Sleeve 5.167,1.104 6.01,1.323 0.844,0.219 10 false Spool Valve

DTC Code DTC Detection Condition Trouble Area
P2759 Open or short is detected in the shift solenoid valve SLU circuit for 1 sec. or more while driving (1-trip detection logic).
·

Open or short in shift solenoid valve SLU circuit

·

Shift solenoid valve SLU

·

TCM



MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLU circuit is detected, the TCM determines there is a malfunction. The TCM will turn on the MIL and store this DTC.

WIRING DIAGRAM

C219217E56
2.802,1.333 3.031,1.5 0.229,0.167 10 false 13 5.469,1.333 5.698,1.5 0.229,0.167 10 false 22 2.323,1.083 2.75,1.281 0.427,0.198 10 false SLU+ 2.813,2.552 3.042,2.719 0.229,0.167 10 false 5 0.823,2.208 1.052,2.375 0.229,0.167 10 false 1 0.823,1.375 1.052,1.542 0.229,0.167 10 false 2 2.323,2.313 2.75,2.51 0.427,0.198 10 false SLU- 5.781,1.229 6.208,1.427 0.427,0.198 10 false SLU+ 5.469,2.552 5.698,2.719 0.229,0.167 10 false 21 5.781,2.448 6.208,2.646 0.427,0.198 10 false SLU- 1.021,2.948 1.448,3.146 0.427,0.198 10 false C30 1.021,3.115 2.271,3.313 1.25,0.198 10 false Transmission Wire 1.042,1.792 2.688,2.021 1.646,0.229 10 false Shift Solenoid Valve SLU 5.958,3.271 6.302,3.438 0.344,0.167 10 false G69 5.948,3.417 6.375,3.615 0.427,0.198 10 false TCM

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)
a.
C214326E09
1.583,1.306 1.384,1.745 false 1.656,1.087 1.911,1.745 false 1.154,1.783 1.561,1.950 0.407,0.167 10 SLU+ 0.055,0.021 0.279,0.187 0.224,0.167 10 *a 1.746,1.783 2.126,1.950 0.380,0.167 10 SLU-

Disconnect the C30 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SLU+) - 5 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
13 (SLU+) - Body ground Always 10 kΩ or higher
5 (SLU-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLU
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.
U169984E02
0.667,2.063 0.385,2.74 false 0.719,2.063 1.302,2.75 false 0.073,0 0.271,0.167 0.198,0.167 10 false *a 0.854,0.385 1.156,0.542 0.302,0.156 10 false G69 0.052,2.781 0.76,3.01 0.708,0.229 10 false 22 (SLU+) 1.083,2.781 1.74,3 0.656,0.219 10 false 21 (SLU-)

Disconnect the G69 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-22 (SLU+) - G69-21 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
G69-22 (SLU+) - Body ground Always 10 kΩ or higher
G69-21 (SLU-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to TCM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR