Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2015.06–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  P2757  Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU)  


DESCRIPTION

The TCM uses the signals from the throttle position sensor, air-flow meter, turbine (input) speed sensor, output speed sensor and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.

C221407E01
4.729,2.135 5.031,1.188 5.031,1.188 5.094,1.188 true 4.969,2.323 5.125,2.688 5.125,2.688 5.188,2.688 true 5.76,2.396 5.917,2.688 5.917,2.688 5.979,2.688 true 6.031,2.594 6.917,2.813 0.885,0.219 10 false Solenoid Coil 0.135,0.688 1.385,0.906 1.25,0.219 10 false Hydraulic Pressure 2.573,3.01 3.135,3.229 0.563,0.219 10 false Current 5.24,2.615 5.771,2.833 0.531,0.219 10 false Sleeve 5.167,1.104 6.01,1.323 0.844,0.219 10 false Spool Valve

Then the TCM compares the engagement condition of the lock-up clutch with the lock-up schedule in the TCM memory to detect mechanical problems of shift solenoid valve SLU, the valve body and torque converter clutch.

DTC Code DTC Detection Condition Trouble Area
P2757 Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up remains ON in the lock-up OFF range (2-trip detection logic).
·

Shift solenoid valve SLU remains open or closed

·

Valve body is blocked

·

Torque converter clutch assembly

·

Automatic transmission (clutch, brake, gear, etc.)

·

Line pressure is too low



MONITOR DESCRIPTION

Torque converter lock-up is controlled by the TCM based on the turbine (input) speed sensor NT, output speed sensor SP2, engine speed, engine load, engine temperature, vehicle speed, transmission temperature and gear selection. The TCM determines the lock-up status of the torque converter by comparing the engine speed (NE) to the input turbine speed (NT). The TCM calculates the actual transmission gear by comparing the input turbine speed (NT) to the output shaft speed (SP2). When conditions are appropriate, the TCM requests lock-up by applying control voltage to shift solenoid SLU. When shift solenoid valve SLU is turned on, it applies pressure to the lock-up relay valve and locks the torque converter clutch.

If the TCM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the TCM interprets this as a fault in shift solenoid valve SLU or the lock-up system performance.

The TCM will turn on the MIL and store the DTC.

Example:

When either of the following is met, the system judges it as a malfunction.

·

There is a difference in speed between the input side (engine speed) and output side (input turbine speed) of the torque converter when the TCM commands lock-up on (the engine speed is at least 70 rpm more than the input turbine speed).

·

There is no difference in speed between the input side (engine speed and output side (input turbine speed) of the torque converter when the TCM commands lock-up off (the difference between the engine speed and input turbine speed is less than 35 rpm).


CAUTION / NOTICE / HINT

ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Active Test.


g.

According to the display on the tester, perform the Active Test.

ECT
Tester Display Test Part Control Range Diagnostic Note
Activate the Lock Up Control shift solenoid valve SLU to set automatic transmission to lock-up ON or OFF Possible to check shift solenoid valve SLU operation.
[Vehicle Condition]
·

Vehicle speed: 70 km/h (44 mph) or more

·

Gear: Highest gear

·

Throttle valve opening angle: Less than 20%



HINT:
·

This test can be conducted when the vehicle speed is 70 km/h (44 mph) or more.

·

This test can be conducted with the 5th gear.




h.

Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

C159073E01
4.531,2.188 5.51,1.958 5.51,1.958 5.573,1.958 false 5.198,2.229 5.542,2.615 5.542,2.615 5.604,2.615 false 0.719,2.677 1.677,2.948 0.958,0.271 10 false Engine Speed 0.719,1.677 1.813,2.156 1.094,0.479 10 false Accelerator Pedal Fully Released 0.719,1.021 1.823,1.542 1.104,0.521 10 false Accelerator Pedal Opening Angle 4.99,3.125 5.438,3.323 0.448,0.198 10 false Time 5.656,1.865 6.615,2.146 0.958,0.281 10 false Lock-up OFF 5.656,2.49 6.646,2.708 0.99,0.219 10 false Lock-up ON

HINT:
·

When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.

·

Slowly release the accelerator pedal in order to decelerate, but do not fully release the pedal.

(Fully releasing the pedal will close the throttle valve and lock-up may be turned off automatically.)





PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P2757)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / DTC.


e.

Read the DTCs using the tester.

Result
Result Proceed to
Only P2757 is output A
P2757 and other DTCs are output B

HINT:

If any other codes besides P2757 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT SHIFT SOLENOID VALVE SLU

B

2.INSPECT SHIFT SOLENOID VALVE SLU
a.
C209928E05
0.057,0.005 0.374,0.207 0.317,0.202 10 *a 1.757,0.949 2.207,0.361 false 2.238,0.194 2.402,0.396 0.164,0.202 10 1 1.506,0.949 1.056,0.361 false 0.918,0.194 1.082,0.396 0.164,0.202 10 2 1.757,2.945 2.207,2.358 false 2.238,2.191 2.402,2.393 0.164,0.202 10 1 1.506,2.945 1.056,2.358 false 0.918,2.191 1.082,2.393 0.164,0.202 10 2 1.923,3.928 2.122,4.130 0.200,0.202 10 (-) 1.119,3.928 1.339,4.130 0.221,0.202 10 (+)

Remove shift solenoid valve SLU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve SLU)


OK

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

4.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY