Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2015.06–2017.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  P0560  System Voltage  


DESCRIPTION

The battery supplies power to the TCM even when the ignition switch is off. This power allows the TCM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the TCM data is cleared and the TCM determines that there is a malfunction in the power supply circuit. The next time the engine is started, the TCM will illuminate the MIL and store the DTC.

DTC Code DTC Detection Condition Trouble Area
P0560 Open in the TCM back-up power source circuit (1-trip detection logic).
·

Open in back-up power source circuit

·

TCM



HINT:

If DTC P0560 is stored, the TCM does not store other DTCs.


WIRING DIAGRAM

C333372E01
2.702,2.412 3.127,2.608 0.425,0.196 10 IG2 6.251,3.15 6.651,3.345 0.400,0.196 10 TCM 6.041,2.615 6.288,2.811 0.247,0.196 10 E1 2.158,1.706 2.583,1.901 0.425,0.196 10 IG2 6.041,1.541 6.466,1.737 0.425,0.196 10 IG2 2.531,1.135 2.829,1.331 0.298,0.196 10 EFI 6.041,1.002 6.538,1.198 0.497,0.196 10 BATT 0.15,1.002 1.187,1.198 1.037,0.196 10 from P/I-B Fuse 5.779,0.81 5.909,1.006 0.130,0.196 10 5 5.69,1.002 5.987,1.198 0.297,0.196 10 G70 3.306,1.002 3.604,1.198 0.297,0.196 10 1B 1.649,1.002 1.946,1.198 0.297,0.196 10 1C 1.66,2.071 1.957,2.267 0.297,0.196 10 1A 3.303,2.071 3.600,2.267 0.297,0.196 10 1A 3.303,1.541 3.600,1.737 0.297,0.196 10 1A 5.69,1.541 5.987,1.737 0.297,0.196 10 G70 5.779,1.346 5.909,1.542 0.130,0.196 10 6 5.69,2.612 5.987,2.808 0.297,0.196 10 G69 5.779,2.42 5.909,2.616 0.130,0.196 10 1 4.582,1.706 4.890,1.901 0.307,0.196 10 INJ 3.833,2.079 5.438,2.601 1.605,0.522 10 from Power Management Control ECU*1, Ignition Switch*2 3.349,0.81 3.479,1.006 0.130,0.196 10 1 3.349,1.339 3.479,1.535 0.130,0.196 10 4 3.349,1.898 3.479,2.094 0.130,0.196 10 1 1.703,0.81 1.833,1.006 0.130,0.196 10 1 1.703,1.887 1.833,2.082 0.130,0.196 10 3 1.825,2.751 3.436,2.946 1.611,0.196 10 No. 1 Integration Relay 0.076,3.101 1.937,3.268 1.861,0.166 10 *1: w/ Entry and Start System 0.076,3.415 2.492,3.581 2.417,0.166 10 *2: w/o Entry and Start System

PROCEDURE

1.CHECK DTC OUTPUT (ECD SYSTEM DTC P0560)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs using the intelligent tester.

Result
Result Proceed to
DTCs are not output A
DTC P0560 (ECD system) is output B



A

2.CHECK TCM (POWER SOURCE, BODY GROUND)

B

2.CHECK TCM (POWER SOURCE, BODY GROUND)
a.
U170117E01
0.887,0.437 1.169,0.596 0.282,0.159 10 G69 2.321,0.433 2.612,0.592 0.291,0.159 10 G70 0.051,0.018 0.245,0.195 0.194,0.177 10 *a 1.194,2.928 1.626,3.084 0.432,0.156 10 1 (E1) 1.896,2.927 2.529,3.083 0.633,0.156 10 5 (BATT) 1.32,1.926 1.445,2.88 false 2.3,1.926 2.205,2.884 false

Disconnect the G69 and G70 TCM connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G70-5 (BATT) - G69-1 (E1) Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-1 (E1) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to TCM)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TCM - BATTERY, BODY GROUND)