Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2015.06–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the TCM.

If the TCM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The TCM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at more than 20 km/h (12.4 mph) for over 20 seconds.

DTC Code DTC Detection Condition Trouble Area
P0617 All conditions are met (1-trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.4 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is ON.
(d) Battery voltage (10.5 V or higher) is applied to the TCM for 20 seconds.
·

Park/neutral position switch

·

Starter relay circuit

·

Cranking holding function circuit

·

TCM



WIRING DIAGRAM

C251065E07
5.792,6.719 6.177,6.948 0.385,0.229 9 false TCM 3.469,5.615 5.458,5.813 1.99,0.198 9 false Park/Neutral Position Switch 0.125,7.365 2.552,7.563 2.427,0.198 9 false *2: w/o Entry and Start System 0.125,6.99 2.479,7.188 2.354,0.198 9 false *1: w/ Entry and Start System 3.458,5.458 3.885,5.688 0.427,0.229 9 false C159 5.292,3.51 5.5,3.688 0.208,0.177 9 false 12 5.344,4.063 5.5,4.24 0.156,0.177 9 false 8 5.354,4.625 5.49,4.802 0.135,0.177 9 false 9 5.333,5.938 5.469,6.115 0.135,0.177 9 false 1 4.885,3.813 5.094,4.021 0.208,0.208 9 false 4 3.729,3.823 3.938,4.031 0.208,0.208 9 false 5 3.313,3.281 3.521,3.49 0.208,0.208 9 false 5 2.542,3.281 2.75,3.49 0.208,0.208 9 false 3 2.542,3.813 2.75,4.021 0.208,0.208 9 false 1 3.323,3.823 3.531,4.031 0.208,0.208 9 false 2 3.719,4.667 3.927,4.875 0.208,0.208 9 false 2 4.885,4.375 5.094,4.583 0.208,0.208 9 false 7 4.896,4.938 5.104,5.146 0.208,0.208 9 false 1 2.854,4.01 3.146,4.25 0.292,0.24 9 false ST 2.771,2.073 3.01,2.229 0.24,0.156 9 false *2 2.76,1.302 3,1.458 0.24,0.156 9 false *1 5.615,2.198 5.958,2.375 0.344,0.177 9 false STA 5.25,2.208 5.594,2.385 0.344,0.177 9 false G69 5.24,3.708 5.583,3.885 0.344,0.177 9 false G69 5.25,4.281 5.594,4.458 0.344,0.177 9 false G71 5.25,4.823 5.594,5 0.344,0.177 9 false G71 5.24,6.135 5.583,6.313 0.344,0.177 9 false G69 5.615,0.688 5.958,0.865 0.344,0.177 9 false STA 5.281,2.031 5.49,2.188 0.208,0.156 9 false 11 5.396,0.823 5.604,1.031 0.208,0.208 9 false 6 5.792,1.344 6.219,1.542 0.427,0.198 9 false ECM 5.792,1.208 6.177,1.417 0.385,0.208 9 false G57 1.448,3.177 2.25,3.458 0.802,0.281 9 false to Starter 0.583,4.552 2.188,4.76 1.604,0.208 9 false from ECU-IG NO. 1 Fuse 0.438,2.208 2.104,2.448 1.667,0.24 10 false from Ignition Switch (ST2) 1.177,1.396 2.052,1.583 0.875,0.188 10 false from ST Fuse 4.688,3.594 4.906,3.823 0.219,0.229 9 false B 3.896,3.615 4.115,3.844 0.219,0.229 9 false L 3.896,4.448 4.115,4.677 0.219,0.229 9 false RB 4.615,4.156 4.833,4.385 0.219,0.229 9 false DL 4.615,4.729 4.833,4.958 0.219,0.229 9 false RL 5.615,3.698 6,3.885 0.385,0.188 9 false NSW 5.615,4.271 6.021,4.458 0.406,0.188 9 false D 5.615,4.823 5.885,5 0.271,0.177 9 false R 5.615,6.135 5.823,6.302 0.208,0.167 9 false E1

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine can be cranked normally. If the engine does not crank, proceed to the problem symptoms table (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the intelligent tester. The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>FREEZE FRAME DATA).



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / Data List.


e.

Read the value displayed on the intelligent tester.


f.

Crank the engine.


g.

Read the value displayed on the intelligent tester.

ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Starter Signal Starter signal/
ON or OFF
·

ON: Engine cranking

·

OFF: Engine not cranking


-

OK:

Starter Signal is only ON when the engine is being started (during cranking).




OK

2.CHECK TCM (STA VOLTAGE)

NG

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.CHECK TCM (STA VOLTAGE)
a.
U169985E02
1.344,2.063 1.688,2.729 false 1.292,1.958 0.906,2.729 false 0.073,0 0.271,0.167 0.198,0.167 10 false *a 0.865,0.396 1.167,0.552 0.302,0.156 10 false G69 1.406,2.781 2.01,3.01 0.604,0.229 10 false 11 (STA) 0.646,2.781 1.156,3 0.51,0.219 10 false 1 (E1)

Disconnect the G69 TCM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G69-11 (STA) - Body ground Ignition switch ON and shift lever in P or N Below 2 V



c.

Turn the ignition switch off.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-1 (E1) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to TCM)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TCM - ST RELAY, BODY GROUND)

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C358777E01
1.281,0.99 0.958,0.438 false 1.615,0.979 1.5,0.396 false 2.448,1.854 2.125,1.302 false 0.771,0.292 1.083,0.49 0.313,0.198 10 false B 2.552,1.833 2.865,2.031 0.313,0.198 10 false L 1.375,0.146 1.688,0.344 0.313,0.198 10 false RB

Disconnect the C159 park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Shift lever in P Below 1 Ω
4 (B) - 5 (L) Shift lever in N Below 1 Ω
4 (B) - 5 (L) Shift lever not in P 10 kΩ or higher
4 (B) - 5 (L) Shift lever not in N 10 kΩ or higher
2 (RB) - 5 (L) Shift lever in P, R, N, D or S 10 kΩ or higher



Text in Illustration
*a Component without harness connected
(Park/Neutral Position Switch)


OK

CHECK ECD SYSTEM (STARTER SIGNAL CIRCUIT)

NG