Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2015.06–2017.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  P2772  Four Wheel Drive (4WD) Low Switch Circuit Range / Performance  


DESCRIPTION

The TCM detects the signal from the transfer L4 position switch.

This DTC indicates that the transfer L4 position switch remains on.

DTC Code DTC Detection Condition Trouble Area
P2772 Transfer L4 position switch remains on while the vehicle is being driven under the following conditions for 1.8 sec. or more (1-trip detection logic):
(a) Output shaft speed is between 1000 and 3000 rpm.
(b) Transfer is in H4.
·

Short in transfer L4 position switch circuit

·

Transfer system

·

TCM



MONITOR DESCRIPTION

The TCM monitors the transfer-case L4 position switch to determine when the transfer-case L4 gears are engaged. If the L4 position switch indicates that the transfer-case L4 gears are engaged under the following conditions, the TCM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL and store the DTC:

·

The transfer-case shifter is in the "H4" position.

·

The transfer-case output shaft speed is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


WIRING DIAGRAM

C214970E19
1.052,2.156 3.063,2.354 2.01,0.198 10 false Four Wheel Drive Control ECU 1.052,1.979 1.448,2.177 0.396,0.198 10 false G53 2.5,1.365 2.896,1.563 0.396,0.198 10 false 21 2.177,1.25 2.573,1.448 0.396,0.198 10 false L4 5.635,1.25 6.135,1.448 0.5,0.198 10 false L4 5.323,1.365 5.563,1.563 0.24,0.198 10 false 15 5.813,2.948 6.313,3.146 0.5,0.198 10 false G71 5.813,3.115 6.313,3.313 0.5,0.198 10 false TCM

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - BODY GROUND)
a.
U169957E02
0.385,1.719 0.531,1.281 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 1.573,0.26 1.948,0.49 0.375,0.229 10 false G53 0.26,1.75 0.51,1.948 0.25,0.198 10 false L4

Disconnect the G53 four wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-21 (L4) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Four Wheel Drive Control ECU)



OK

NG

2.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - TCM)
2.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - TCM)
a.
U169987E02
1.531,2.063 1.198,2.469 false 0.198,0.063 0.469,0.292 0.271,0.229 10 false *a 0.875,2.542 1.427,2.74 0.552,0.198 10 false 15 (L4) 1.594,0.448 1.875,0.594 0.281,0.146 10 false G71

Disconnect the G71 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G71-15 (L4) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to TCM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR