Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › SHIFT LEVER › 2015.06–2017.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260775 SHIFT LEVER A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSTALLATION  


PROCEDURE

Hide 33550 1.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

NOTICE:

Check that the park/neutral position switch assembly and the shift lever are in N.


a.
U148447E01
1.017,2.844 1.136,3.003 0.118,0.160 10 3 2.548,1.896 2.666,2.055 0.118,0.160 10 4 2.672,2.825 2.790,2.984 0.118,0.160 10 2 1.035,2.065 1.153,2.225 0.118,0.160 10 1

Install the transmission floor shift assembly with the 4 bolts tighten the bolt in the order shown in the illustration.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


b.

Connect the 2 connectors.


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Turn the socket of the transmission control cable assembly 180° counterclockwise. While holding the socket in place, push in the lock piece until the lock piece clicks twice.

C216621E02
1.617,1.223 1.617,1.453 1.617,1.453 1.853,1.453 false 1.56,0.543 1.56,0.328 1.56,0.328 1.326,0.328 false 1.875,1.381 2.046,1.536 0.171,0.155 10 *1 1.161,0.252 1.341,0.413 0.180,0.161 10 *2 3.706,0.101 3.887,0.262 0.180,0.161 10 *a

Text in Illustration
*1 Socket *2 Lock Piece
*a Push in - -

NOTICE:

Do not over-rotate the socket as it will come off the internal spring and the transmission control cable assembly will not be reusable.


HINT:

If the lock piece cannot be pushed in, slightly turn the socket clockwise and then push in the lock piece again.



b.

Install the outer part of the transmission control cable assembly to the transmission floor shift assembly retainer. Check that the socket and lock piece are positioned at original position.

C216998E02
1.396,1.26 1,1.51 1,1.51 0.906,1.51 true 0.75,1.448 0.938,1.615 0.188,0.167 10 false *1

Text in Illustration
*1 Transmission Floor Shift Assembly Retainer - -


c.
C203381E05
1.813,1.01 1.677,0.479 1.677,0.479 1.573,0.479 true 1.844,2.229 1.76,1.917 1.76,1.917 1.667,1.917 false 2.448,2.094 2.365,1.792 2.365,1.792 2.469,1.792 false 2.344,1.135 2.427,1.448 2.427,1.448 2.521,1.448 false 1.354,0.385 1.521,0.552 0.167,0.167 10 false *1 1.458,1.833 1.625,2 0.167,0.167 10 false *1 2.49,1.698 2.698,1.885 0.208,0.188 10 false *2 2.542,1.354 2.75,1.542 0.208,0.188 10 false *2

Slide the slider in the direction shown in the illustration and pull out the lock piece.

Text in Illustration
*1 Slider
*2 Lock Piece


d.
C204586

Connect the end of the cable to the shift lever.

NOTICE:
·

The shift lever should be in N.

·

Make sure that the lock piece is pulled up.

·

Push on the end of the cable all the way to the base of the pin.




e.
U115849

Push the lock piece into the adjuster case and lock it.

NOTICE:

Make sure that the lock piece is completely locked by the slider.