Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV) › 2015.06–2017.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260782 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)  P2773  Four Wheel Drive (4WD) Low Switch Circuit Low  


DESCRIPTION

The ECM detects the signal from the transfer L4 position switch.

This DTC indicates that the transfer L4 position switch remains on.

DTC Code DTC Detection Condition Trouble Area
P2773 Transfer L4 position switch remains on while the vehicle is being driven under the following conditions for 1.8 seconds or more (1 trip detection logic):
(a) Output shaft speed is between 1000 and 3000 rpm.
(b) Transfer position switch is in H4.
·

Short in transfer L4 position switch circuit

·

Transfer system

·

ECM



MONITOR DESCRIPTION

The ECM monitors the transfer case L4 position switch to determine when the transfer case L4 gears are engaged. If the transfer case L4 gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL and store the DTC:

·

The L4 switch indicates that the L4 transfer case gears are engaged.

·

The transfer position switch is in H4.

·

The transfer case output shaft speed is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


WIRING DIAGRAM

C328828E03
0.669,3.079 2.676,3.274 2.007,0.196 10 4 Wheel Drive Control ECU 0.669,2.898 1.062,3.094 0.392,0.196 10 G53 5.014,1.977 5.515,2.173 0.502,0.196 10 L4 2.059,1.977 2.560,2.173 0.502,0.196 10 L4 5.841,1.07 6.343,1.266 0.502,0.196 10 12 V 4.721,1.977 5.050,2.173 0.329,0.196 10 12 2.365,1.977 2.601,2.173 0.236,0.196 10 21 5.425,2.898 5.927,3.094 0.502,0.196 10 C152 5.425,3.079 5.927,3.274 0.502,0.196 10 ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV)>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)
a.
U148300E01
0.385,1.719 0.531,1.281 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 1.594,0.25 1.969,0.479 0.375,0.229 10 false G53 0.26,1.75 0.51,1.948 0.25,0.198 10 false L4

Disconnect the G53 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-21 (L4) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)



OK

NG

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
a.
U170428E02
1.927,1.885 1.563,2.698 false 0.115,0.094 0.625,0.302 0.51,0.208 10 false *a 1.802,0.229 2.313,0.438 0.51,0.208 10 false C152 1.219,2.75 2.031,2.958 0.813,0.208 10 false 12 (L4)

Disconnect the G53 4 wheel drive control ECU connector.


b.

Disconnect the C152 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C152-12 (L4) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR