Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL SYSTEM › 2015.06–2017.08
RM27T0E _52 Drivetrain _053705 AXLE AND DIFFERENTIAL _0260859 DIFFERENTIAL SYSTEM G

AXLE AND DIFFERENTIAL  DIFFERENTIAL SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT DIFFERENTIAL LOCK SYSTEM

a.

Inspect the indicator light.

i.

Check that the indicator light lights up approximately 1 second after the ignition switch is turned to ON.



b.

Inspect the differential lock operation.

i.

Jack up the vehicle and start the engine.


ii.

Set the transfer to L4 or L4L.


iii.

When the differential lock control switch is set to the ON position, check that the indicator light turns on. Differential lock is applied to the rear wheels at this time.

HINT:

If the gears of the differential lock system are not engaged, the indicator light continues blinking, so rotate the tires to engage the gears.



iv.

When the differential lock control switch is in the OFF position, check that the indicator light goes off. The rear differential lock is released at this time.


v.

Stop the engine and lower the vehicle.



Hide 89533A 2.INSPECT FOUR WHEEL DRIVE CONTROL ECU (POWER SUPPLY)

U148194E01
2.338,1.411 2.646,1.567 0.309,0.156 10 G54 1.747,1.188 1.961,1.357 0.215,0.170 10 IG 2.283,1.916 1.964,1.273 false 0.175,0.056 0.465,0.285 0.290,0.229 10 *a 1.501,2.657 1.879,2.834 0.378,0.177 10 GND 2.167,1.982 2.025,2.743 false 2.025,2.743 1.914,2.743 false

a.

Check the harness and connector (ECU - battery and body ground).

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G54-3 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Component with harness connected
(4 wheel drive control ECU)

If the result is not as specified, inspect the harness and connector or 4WD fuse. If the harness is malfunctioning, repair or replace the harness and connector or 4WD fuse. If the harness and connector are normal, replace the 4 wheel drive control ECU (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL ECU>REMOVAL).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-4 (GND) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the harness or connector.



Hide 55936E 3.INSPECT CENTER CLUSTER MODULE SWITCH (REAR DIFFERENTIAL LOCK CONTROL SWITCH) (w/ Combination Switch)

a.

Check the harness and connector (center cluster module switch (rear differential lock control switch) - ECU).

i.

Disconnect the G53 ECU connector.


ii.

Disconnect the G156 switch connector.


iii.

Measure the resistance according to the value(s) in the table below.

U148961E03
3.875,0.906 3.875,0.219 3.875,0.219 4.021,0.219 false 2.635,1.094 2.635,1.49 2.635,1.49 2.833,1.49 false 1.604,1.104 1.604,1.51 1.604,1.51 1.438,1.51 false 4.625,0.24 4.938,0.396 0.313,0.156 10 false G53 1.844,0.24 2.229,0.396 0.385,0.156 10 false G156 1.313,1.448 1.448,1.635 0.135,0.188 10 false B 2.854,1.417 3.042,1.604 0.188,0.188 10 false E 4.052,0.156 4.26,0.323 0.208,0.167 10 false R 0.49,0.115 0.677,0.354 0.188,0.24 10 false *a 3.229,0.104 3.479,0.292 0.25,0.188 10 false *b

Text in Illustration
*a Front view of wire harness connector
(to center cluster module switch (rear differential lock control switch))
*b Front view of wire harness connector
(to 4 wheel drive control ECU)

Standard Resistance:
Tester Connection Condition Specified Condition
G156-15 (B) - G53-3 (R) Always Below 1 Ω
G156-24 (E) - Body ground Always Below 1 Ω
G156-24 (E) - G53-3 (R) Always 10 kΩ or higher


If the result is not as specified, repair or replace the harness or connector.



b.

Check the center cluster module switch (rear differential lock control switch).

i.

Turn the ignition switch to ON.


ii.

Connect the G156 switch connector.


iii.

Connect the G53 ECU connector.


iv.
U148195E01
1.091,1.079 1.399,1.235 0.309,0.156 10 G53 0.175,0.106 0.465,0.335 0.290,0.229 10 *a 1.42,1.388 1.597,1.564 0.177,0.177 10 R 1.801,2.047 1.712,1.469 false 1.712,1.469 1.592,1.469 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G53-3 (R) - Body ground center cluster module switch (rear differential lock control switch) on Below 1.5 V
center cluster module switch (rear differential lock control switch) off 11 to 14 V


Text in Illustration
*a Component with harness connected
(4 wheel drive control ECU)



Hide 84725A 4.INSPECT DIFFERENTIAL LOCK SWITCH (w/o Combination Switch)

a.

Check the harness and connector (differential lock switch - ECU).

i.

Disconnect the G53 ECU connector.


ii.

Disconnect the G110 switch connector.


iii.

Measure the resistance according to the value(s) in the table below.

U170245E02
1.552,1.625 1.552,1.938 1.552,1.938 1.396,1.938 false 1.927,1.625 1.927,1.938 1.927,1.938 2.083,1.938 false 4.063,1.365 4.063,0.615 4.063,0.615 4.219,0.615 false 4.823,0.573 5.135,0.729 0.313,0.156 10 false G53 1.552,0.573 1.938,0.729 0.385,0.156 10 false G110 1.26,1.875 1.646,2.063 0.385,0.188 10 false E 2.177,1.865 2.365,2.052 0.188,0.188 10 false B 4.281,0.552 4.49,0.719 0.208,0.167 10 false R 0.833,0.177 1.021,0.417 0.188,0.24 10 false *a 3.521,0.177 3.771,0.365 0.25,0.188 10 false *b

Text in Illustration
*a Front view of wire harness connector
(to differential lock switch)
*b Front view of wire harness connector
(to 4 wheel drive control ECU)

Standard Resistance:
Tester Connection Condition Specified Condition
G110-6 (B) - G53-3 (R) Always Below 1 Ω
G110-3 (E) - Body ground Always Below 1 Ω
G110-3 (E) - G53-3 (R) Always 10 kΩ or higher


If the result is not as specified, repair or replace the harness or connector.



b.

Check the center cluster module switch (rear differential lock control switch).

i.

Turn the ignition switch to ON.


ii.

Connect the G110 switch connector.


iii.

Connect the G53 ECU connector.


iv.
U148195E01
1.091,1.079 1.399,1.235 0.309,0.156 10 G53 0.175,0.106 0.465,0.335 0.290,0.229 10 *a 1.42,1.388 1.597,1.564 0.177,0.177 10 R 1.801,2.047 1.712,1.469 false 1.712,1.469 1.592,1.469 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G53-3 (R) - Body ground differential lock switch on Below 1.5 V
differential lock switch off 11 to 14 V


Text in Illustration
*a Component with harness connected
(4 wheel drive control ECU)



Hide 5.INSPECT REAR DIFFERENTIAL LOCK SHIFT ACTUATOR

a.

Check the harness and connector (rear differential lock actuator - ECU).

i.

Disconnect the E1 differential lock actuator connector.


ii.

Disconnect the G53 and G54 ECU connectors.


iii.

Measure the resistance according to the value(s) in the table below.

C358686E01
0.948,1.427 1.198,1.427 1.198,1.427 1.406,0.969 true 2.021,1.396 1.771,1.396 1.771,1.396 1.521,0.979 true 6.521,1.552 6.271,1.552 6.271,1.552 6.021,1.135 true 2.719,1.583 2.969,1.583 2.969,1.583 3.177,1.125 true 2.708,0.365 2.958,0.365 2.958,0.365 3.188,0.823 true 5.313,0.385 5.563,0.385 5.563,0.385 5.792,0.844 true 5.354,1.594 5.604,1.594 5.604,1.594 5.813,1.135 true 6.469,0.594 6.219,0.594 6.219,0.594 6.042,0.896 true 5.281,1.094 5.615,1.094 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.469,0.313 1.781,0.51 0.313,0.198 10 false G53 3.542,0.323 3.854,0.521 0.313,0.198 10 false G54 5.76,0.281 6.073,0.479 0.313,0.198 10 false E1 0.563,1.354 1.115,1.552 0.552,0.198 10 false RLY1 2.083,1.333 2.635,1.531 0.552,0.198 10 false RLY2 2.49,1.51 3.042,1.708 0.552,0.198 10 false M2 5.052,0.323 5.604,0.521 0.552,0.198 10 false M2 5.073,0.083 5.625,0.281 0.552,0.198 10 false *b 2.479,0.281 3.031,0.479 0.552,0.198 10 false M1 4.927,1.51 5.479,1.708 0.552,0.198 10 false RLY2 6.573,1.469 7.125,1.667 0.552,0.198 10 false RLY1 6.552,0.49 7.104,0.688 0.552,0.198 10 false M1 4.906,1.01 5.458,1.208 0.552,0.198 10 false GND

Text in Illustration
*a Front view of wire harness connector
(to 4 wheel drive control ECU)
*b Front view of wire harness connector
(to Differential Lock Shift Actuator)

Standard Resistance:
Tester Connection Condition Specified Condition
G53-10 (RLY2) - E1-5 (RLY2) Always Below 1 Ω
G53-10 (RLY2) - Body ground Always 10 kΩ or higher
G53-9 (RLY1) - E1-6 (RLY1) Always Below 1 Ω
G53-9 (RLY1) - Body ground Always 10 kΩ or higher
G54-5 (M2) - E1-2 (M2) Always Below 1 Ω
G54-5 (M2) - Body ground Always 10 kΩ or higher
G54-1 (M1) - E1-3 (M1) Always Below 1 Ω
G54-1 (M1) - Body Ground Always 10 kΩ or higher
E1-4 (GND2) - Body Ground Always Below 1 Ω




b.

Check the free to lock switch.

i.

Connect lines via a relay as shown in the illustration and check that the actuator fork moves from the free to the lock position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEF relay.


C217754E11
1.281,2.938 1.177,2.531 false 1.177,2.531 1.073,2.531 false 2,2.469 1.875,2.469 false 1.875,2.469 1.656,2.948 false 1.906,3.354 2.156,3.688 false 2.156,3.688 2.271,3.688 false 1.594,3.333 1.594,3.75 false 1.323,3.333 1.115,3.74 false 1.115,3.74 0.927,3.74 false 6.031,2.948 5.594,3.094 false 5.594,3.094 5.49,3.094 false 5.531,2.396 5.656,2.396 false 5.656,2.396 6.052,2.51 false 5.625,1.625 5.771,1.625 false 5.781,1.625 5.948,2.01 false 6.854,1.583 6.698,1.583 false 6.698,1.583 6.531,2.052 false 6.24,1.979 6.24,1.292 false 6.24,1.292 5.969,1.292 false 0.854,2.458 1.094,2.635 0.24,0.177 10 false M1 2.031,2.396 2.271,2.573 0.24,0.177 10 false M2 2.313,3.604 2.75,3.792 0.438,0.188 10 false GND2 1.438,3.792 1.885,3.979 0.448,0.188 10 false RLY2 0.542,3.677 0.99,3.865 0.448,0.188 10 false RLY1 5.469,1.552 5.646,1.74 0.177,0.188 10 false 1 6.896,1.5 7.063,1.667 0.167,0.167 10 false 2 5.385,2.313 5.552,2.521 0.167,0.208 10 false 5 5.333,3.031 5.5,3.198 0.167,0.167 10 false 3 5.688,0.729 6.01,0.896 0.323,0.167 10 false *1 5.833,1.229 6.031,1.417 0.198,0.188 10 false 4 0.375,0.115 0.615,0.323 0.24,0.208 10 false *a

Text in Illustration
*1 DEF Relay - -
*a Front view of wire harness connector
(to Differential Lock Shift Actuator)
- -


ii.

After the free to lock switch is complete, check the limit switch.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (RLY2) - 4 (GND2) After free to lock switch is complete Below 12.5 Ω
6 (RLY1) - 4 (GND2) After free to lock switch is complete 500 kΩ or higher


If the result is not as specified, replace the differential lock shift actuator assembly.



c.

Check the lock to free switch.

i.

Connect lines via a relay as shown in the illustration and check that the actuator fork moves from the lock to the free position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEF relay.


C217805E04
0.701,2.515 0.998,2.718 0.297,0.202 10 M1 1.157,2.976 1.022,2.602 false 1.022,2.602 0.935,2.602 false 1.976,2.404 2.236,2.574 0.260,0.170 10 M2 1.505,2.972 1.824,2.472 false 1.824,2.472 1.95,2.472 false 0.534,3.51 0.919,3.686 0.385,0.177 10 RLY1 1.194,3.334 0.988,3.588 false 0.987,3.586 0.908,3.586 false 1.809,3.702 2.194,3.879 0.385,0.177 10 RLY2 1.558,3.323 1.654,3.768 false 1.654,3.768 1.775,3.768 false 2.324,3.532 2.929,3.702 0.605,0.170 10 GND2 1.766,3.334 2.091,3.606 false 2.091,3.606 2.293,3.606 false 5.178,1.431 5.354,1.650 0.177,0.218 10 1 5.738,1.939 5.441,1.493 false 5.441,1.493 5.328,1.493 false 6.724,1.366 6.894,1.564 0.170,0.198 10 2 6.314,1.898 6.521,1.447 false 6.521,1.447 6.668,1.447 false 5.063,2.221 5.233,2.419 0.170,0.198 10 5 5.818,2.446 5.365,2.289 false 5.368,2.293 5.217,2.293 false 5.133,2.797 5.323,2.960 0.191,0.163 10 3 5.824,2.857 5.308,2.857 false 5.6,0.587 5.851,0.792 0.251,0.205 10 *1 5.559,1.076 5.715,1.296 0.156,0.221 10 4 6.01,1.877 6.01,1.148 false 6.01,1.148 5.731,1.148 false 0.201,0.097 0.459,0.308 0.258,0.211 10 *a

Text in Illustration
*1 DEF Relay - -
*a Front view of wire harness connector
(to Differential Lock Shift Actuator)
- -


ii.

After the lock to free switch is complete, check the limit switch.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (RLY2) - 4 (GND2) After lock to free switch is complete 500 kΩ or higher
6 (RLY1) - 4 (GND2) After lock to free switch is complete Below 12.5 Ω


If the result is not as specified, replace the differential lock shift actuator assembly.



Hide 6.INSPECT DIFFERENTIAL LOCK POSITION SWITCH

a.

Inspect the rear differential lock position switch.


ii.
C163511E06
1.045,1.904 1.216,2.079 0.172,0.175 10 *b 1.049,2.675 1.220,2.850 0.172,0.175 10 *c 2.386,0.309 2.639,0.537 0.253,0.229 10 *a 1.63,1.714 1.880,1.891 0.250,0.177 10 +B 2.3,1.358 2.048,1.82 false 2.048,1.82 1.918,1.82 false 2.991,1.706 3.349,1.896 0.358,0.190 10 GND 2.69,1.359 2.859,1.805 false 2.859,1.805 2.936,1.805 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (+B) - 1 (GND) Pushed Below 1 Ω
Released 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Rear Differential Lock Position Switch)
*b Pushed
*c Released

If the result is not as specified, replace the rear differential lock position switch.



b.

Check the harness and connector (ECU - differential lock position switch).

i.

Disconnect the E2 differential lock position switch connector.


ii.

Disconnect the G53 ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

C358687E01
0.969,2.25 1.219,2.25 1.219,2.25 1.469,1.667 true 2.396,2.25 2.083,2.25 2.083,2.25 1.865,1.667 true 6.458,0.792 6.146,0.792 6.146,0.792 5.927,1.365 true 0.615,2.177 1.073,2.375 0.458,0.198 10 false GND 2.49,2.156 2.948,2.354 0.458,0.198 10 false +B 1.563,0.5 2.021,0.698 0.458,0.198 10 false E2 1.573,0.177 2.031,0.375 0.458,0.198 10 false *a 5.208,0.188 5.667,0.385 0.458,0.198 10 false *b 5.156,0.5 5.615,0.698 0.458,0.198 10 false G53 6.5,0.708 6.958,0.906 0.458,0.198 10 false RLP

Text in Illustration
*a Component without harness connected
(Rear Differential Lock Position Switch)
*b Component without harness connected
(4 wheel drive control ECU)

Standard Resistance:
Tester Connection Condition Specified Condition
G53-15 (RLP) - E2-2 (+B) Always Below 1 Ω
G53-15 (RLP) - Body ground Always 10 kΩ or higher
E2-1 (GND) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the harness or connector.