Home › Suspension › SUSPENSION CONTROL › KINETIC DYNAMIC SUSPENSION SYSTEM › 2015.06–2020.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260886 KINETIC DYNAMIC SUSPENSION SYSTEM C

SUSPENSION CONTROL  KINETIC DYNAMIC SUSPENSION SYSTEM  C1812/12  Pressure Sensor Malfunction / Upside  


DESCRIPTION

In the KDSS hydraulic circuit, the fluid is contained under pressure. If the fluid temperature is 20°C (68°F), the pressure is approximately 3.0 MPa (30.6 kgf/cm2, 435 psi).

DTC Code DTC Detection Condition Trouble Area
C1812/12 One of the following conditions continues is met:
·

The sensor power source voltage (SBP1 terminal) is 4.3 V or less for 0.5 seconds with the ignition switch ON.

·

The sensor power source voltage (SBP1 terminal) is 5.5 V or higher for 0.5 seconds with the ignition switch ON.

·

The sensor output (SOP1 terminal) is 0.3 V or less for a second with the ignition switch ON.

·

The sensor output (SOP1 terminal) is 4.7 V or higher for a second with the ignition switch ON.


·

Harness or connector

·

Accumulator pressure sensor (Stabilizer control with accumulator housing assembly)

·

Stabilizer control ECU



WIRING DIAGRAM

C215167E07
4.302,3.729 4.698,3.927 0.396,0.198 10 false G123 4.302,3.906 5.781,4.104 1.479,0.198 10 false Stabilizer Control ECU 5.208,0.719 6.396,1.073 1.188,0.354 10 false Constant Voltage Circuit 5.229,1.771 6.375,1.958 1.146,0.188 10 false Detection Circuit 4.375,1.063 4.854,1.26 0.479,0.198 10 false SBP1 4.354,1.688 4.813,1.906 0.458,0.219 10 false SOP1 4.323,2.344 4.771,2.542 0.448,0.198 10 false SGP1 4.344,2.958 4.74,3.167 0.396,0.208 10 false GND 4.063,1.042 4.323,1.26 0.26,0.219 10 false 15 4.063,1.677 4.344,1.896 0.281,0.219 10 false 17 4.104,2.323 4.292,2.542 0.188,0.219 10 false 6 4.063,2.958 4.302,3.188 0.24,0.229 10 false 22 2.104,1.073 2.583,1.271 0.479,0.198 10 false SBP1 2.094,1.688 2.552,1.906 0.458,0.219 10 false SOP1 2.115,2.344 2.563,2.542 0.448,0.198 10 false SGP1 2.625,1.021 2.813,1.229 0.188,0.208 10 false 3 2.615,1.677 2.813,1.885 0.198,0.208 10 false 2 2.625,2.344 2.865,2.531 0.24,0.188 10 false 1 0.729,1.656 1.844,1.813 1.115,0.156 10 false Pressure Sensor 0.354,3.229 3.313,3.604 2.958,0.375 10 false Accumulator Pressure Sensor (Stabilizer Control with Accumulator Housing Assembly) 0.354,3.063 0.708,3.26 0.354,0.198 10 false R20

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (OIL PRESSURE SENSOR)
NOTICE:
·

Perform the inspection on a level surface.

·

Perform the inspection with the vehicle empty.

·

Make sure that the wheels are on the ground and facing straight ahead.

·

Perform the inspection with the vehicle load completely on the suspension.



a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / KDSS / Data List.


f.

Select the item below in the Data List, and read the value displayed on the intelligent tester.

KDSS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Oil Pressure Sensor Oil pressure sensor/
Min.: -784.79 MPa (-8002.66 kgf/cm2, -113794.55 psi)
Max.: 784.76 MPa (8002.35 kgf/cm2, 113790.20 psi)
2.6 MPa (26.5 kgf/cm2, 377 psi) to 3.0 MPa (30.6 kgf/cm2, 435 psi): When vehicle stopped and fluid temperature 20°C (68°F) -


g.

Check the fluid pressure.

OK:

2.6 MPa (26.5 kgf/cm2, 377 psi) to 3.0 MPa (30.6 kgf/cm2, 435 psi)




OK

2.RECONFIRM DTC

NG

3.INSPECT STABILIZER CONTROL ECU (SBP1 VOLTAGE)
2.RECONFIRM DTC

b.

Check for DTCs (See page Suspension>SUSPENSION CONTROL>KINETIC DYNAMIC SUSPENSION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE STABILIZER CONTROL ECU

B

3.INSPECT STABILIZER CONTROL ECU (SBP1 VOLTAGE)
a.

Connect the stabilizer control ECU connector.


b.

Disconnect the Stabilizer control with accumulator housing connector.


c.
U148486E04
1.635,1.156 1.125,1.646 1.125,1.646 0.958,1.646 false 0.083,0.01 0.271,0.167 0.188,0.156 10 false *a 1.594,0.271 1.875,0.438 0.281,0.167 10 false R20 0.469,1.573 0.854,1.76 0.385,0.188 10 false SBP1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R20-3 (SBP1) - Body ground Ignition switch ON 4.75 to 5.25 V


Text in Illustration
*a Front view of wire harness connector
(to Stabilizer Control with Accumulator Housing Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - ACCUMULATOR PRESSURE SENSOR)

NG

7.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - ACCUMULATOR PRESSURE SENSOR)
4.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - ACCUMULATOR PRESSURE SENSOR)
a.

Disconnect the Stabilizer control ECU connector.


b.

Disconnect the Stabilizer control with accumulator housing connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G123-17 (SOP1) - R20-2 (SOP1) Always Below 1 Ω
G123-17 (SOP1) - Body ground Always 10 kΩ or higher
G123-6 (SGP1) - R20-1 (SGP1) Always Below 1 Ω
G123-6 (SGP1) - Body ground Always 10 kΩ or higher




OK

5.INSPECT ACCUMULATOR PRESSURE SENSOR (OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ACCUMULATOR PRESSURE SENSOR (OUTPUT VOLTAGE)
a.

Connect the stabilizer control ECU connector.


b.

Connect the Stabilizer control with accumulator housing connector.


c.
U148523E01
0.127,0.152 0.431,0.335 0.304,0.184 10 *a 2.751,0.507 3.143,0.672 0.392,0.165 10 SOP1 2.529,1.264 2.557,0.576 2.557,0.576 2.716,0.576 false 1.545,0.604 1.962,0.760 0.417,0.156 10 G123

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G123-17 (SOP1) - Body ground Ignition switch ON 0.4 to 4.6 V


Text in Illustration
*a Component with harness connected
(Stabilizer Control ECU)



OK

REPLACE STABILIZER CONTROL ECU

NG

6.READ VALUE USING INTELLIGENT TESTER (OIL PRESSURE SENSOR)
6.READ VALUE USING INTELLIGENT TESTER (OIL PRESSURE SENSOR)
a.

Disconnect the Stabilizer control with accumulator housing connector.


b.

Connect the stabilizer control ECU connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Chassis / KDSS / Data List.


g.

Select the item below in the Data List, and read the value displayed on the intelligent tester.

KDSS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Oil Pressure Sensor Oil pressure sensor/
Min.: -784.79 MPa (-8002.66 kgf/cm2, -113794.55 psi)
Max.: 784.76 MPa (8002.35 kgf/cm2, 113790.20 psi)
2.6 MPa (26.5 kgf/cm2, 377 psi) to 3.0 MPa (30.6 kgf/cm2, 435 psi): When vehicle stopped and fluid temperature 20°C (68°F) -


h.
U148484E03
0.573,0.708 0.74,0.708 0.74,0.708 1.219,1.208 false 1.479,1.219 2.583,0.76 2.583,0.76 2.75,0.76 false 1.573,0.333 1.854,0.49 0.281,0.156 10 false R20 0.104,0.031 0.375,0.24 0.271,0.208 10 false *a 1.667,1.885 1.917,2.094 0.25,0.208 10 false (+) 1.677,2.531 1.865,2.698 0.188,0.167 10 false (-) 0.156,0.625 0.552,0.781 0.396,0.156 10 false SGP1 2.792,0.688 3.188,0.844 0.396,0.156 10 false SOP1

Using a 1.5 V dry cell battery, connect the positive (+) lead to terminal 2 (SOP1) of the stabilizer control with accumulator housing connector and the negative (-) lead to terminal 1 (SGP1), and check that the Data List display changes.

OK:

Data List display changes.


Text in Illustration
*a Front view of wire harness connector
(to Stabilizer Control with Accumulator Housing Assembly)



OK

REPLACE STABILIZER CONTROLWITH ACCUMULATORHOUSING ASSEMBLY

NG

REPLACE STABILIZER CONTROL ECU

7.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - ACCUMULATOR PRESSURE SENSOR)
a.

Disconnect the Stabilizer control ECU connector.


b.

Disconnect the Stabilizer control with accumulator housing connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G123-15 (SBP1) - R20-3 (SBP1) Always Below 1 Ω
G123-15 (SBP1) - Body ground Always 10 kΩ or higher




OK

REPLACE STABILIZER CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR