Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › 2015.06–2017.08
RM27T0E _53 Suspension _053708 FRONT SUSPENSION _0260889 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING (w/ Air Suspension)

a.
G021681E08
1.854,1.083 0.906,0.885 false 0.635,0.792 0.875,0.979 0.24,0.188 10 false *a 0.313,1.635 0.552,1.823 0.24,0.188 10 false *b 2.333,1.667 2.573,1.854 0.24,0.188 10 true *c

Install the coil spring to the vehicle body with the lower end of the coil spring facing the rear side of the vehicle.

Text in Illustration
*a Lower End
*b Outer Side
*c Rear Side


b.
G021670

Install the 3 nuts to the top of the front shock absorber with coil spring.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


c.
C099159

Temporarily install the bolt, washer and nut as shown in the illustration.


d.
C115604E01
2.697,1.012 3.131,1.217 0.434,0.205 10 SST 2.697,1.081 2.499,1.081 false 2.499,1.081 2.242,1.778 false

Using SST, install the bracket with the nut.

SST
09961-00950  

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


e.
G021668

Using a 4 mm hexagon wrench, install the absorber control actuator with the 2 bolts.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


f.

Attach the 3 clamps and connect the connector.


Hide 2.TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING (w/o Air Suspension)

a.
G021681E09
1.854,1.083 0.906,0.885 false 0.635,0.792 0.875,0.979 0.24,0.188 10 false *a 0.313,1.635 0.552,1.823 0.24,0.188 10 false *b 2.333,1.667 2.573,1.854 0.24,0.188 10 true *c

Install the coil spring to the vehicle body with the lower end of the coil spring facing the rear side of the vehicle.

Text in Illustration
*a Lower End
*b Outer Side
*c Rear Side


b.
C099160

Install the 3 nuts to the upper side of the front shock absorber with coil spring.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


c.
C099159

Temporarily install the bolt, washer and nut as shown in the illustration.


Hide 48626 3.CONNECT FRONT LOWER BALL JOINT ATTACHMENT LH

a.

Connect the front lower ball joint attachment with the 2 bolts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 48811 4.INSTALL FRONT STABILIZER BAR (w/ KDSS)

Hide 5.INSTALL FRONT STABILIZER END BRACKET (w/ KDSS)

Hide 48811 6.INSTALL FRONT STABILIZER BAR (w/o KDSS)

Hide 48829A 7.INSTALL FRONT NO. 1 STABILIZER BRACKET LH (w/o KDSS)

Hide 48824A 8.INSTALL FRONT NO. 1 STABILIZER BRACKET RH (w/o KDSS)

Hide 48810 9.CONNECT FRONT STABILIZER LINK ASSEMBLY LH (w/o KDSS)

a.
C099158

Connect the stabilizer link to the steering knuckle with the nut.

Torque:
70 N*m (710 kgf*cm, 52 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.



Hide 48820B 10.CONNECT FRONT STABILIZER LINK ASSEMBLY RH (w/o KDSS)

HINT:

Use the same procedure described for the LH side.


Hide 11.INSTALL FRONT SUSPENSION MEMBER BRACE SUB-ASSEMBLY

Hide 51405A 12.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 14.INSTALL FRONT WHEEL

Torque:
for Aluminum Wheel : 103 N*m (1050 kgf*cm, 76 ft.*lbf)
for Steel Wheel : 112 N*m (1137 kgf*cm, 82 ft.*lbf)

Hide 15.STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Bounce the vehicle up and down several times to stabilize the suspension.


Hide 16.TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C099159

Tighten the nut.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 17.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

a.

Inspect and adjust the front wheel alignment (See page Suspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT).