Home › Suspension › FRONT SUSPENSION › FRONT STABILIZER BAR (w/ KDSS)
RM27T0E _53 Suspension _053708 FRONT SUSPENSION _0260892 FRONT STABILIZER BAR(w/ KDSS) A

FRONT SUSPENSION  FRONT STABILIZER BAR(w/ KDSS)  INSTALLATION  


PROCEDURE

Hide 48820B 1.TEMPORARILY INSTALL FRONT STABILIZER LINK ASSEMBLY RH

a.
C214458E01
1.414,1.101 1.734,1.424 0.319,0.323 1.453,1.122 1.652,1.308 0.199,0.185 10 *a 1.453,1.223 1.159,1.223 false 1.159,1.223 0.919,0.764 false

Temporarily install the front stabilizer link assembly and spacer with the bolt.

HINT:

Make sure that the identification mark on the front stabilizer link assembly faces inward and toward the front of the vehicle.


Text in Illustration
*a Mark Position


Hide 48870 2.TEMPORARILY INSTALL FRONT STABILIZER WITH TUBE CYLINDER ASSEMBLY

a.

Install the 2 bleeder plug caps to the front stabilizer with tube cylinder assembly.


b.
C214456

Temporarily install the front stabilizer with tube cylinder assembly with the nut and bolt.

HINT:

Pass the tube side of the front stabilizer with tube cylinder assembly under the return tube sub-assembly before installing it.


NOTICE:
·

Turn the bolt while holding the nut.

·

Do not hold the front stabilizer with tube cylinder assembly by the cylinder boot.




Hide 48890 3.CONNECT NO. 1 FRONT STABILIZER CONTROL TUBE ASSEMBLY

a.

Apply suspension fluid to the threads of the flare nuts.


b.

Using a union nut wrench, connect the No. 1 front stabilizer control tube to the front stabilizer with tube cylinder assembly and tighten the flare nuts.

Torque:
44 N*m (450 kgf*cm, 33 ft.*lbf)

HINT:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



c.

Tighten the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51419 4.INSTALL FRAME APRON SEAL BRACKET

a.

Install the bracket with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 48811 5.INSTALL FRONT STABILIZER BAR

a.
C214685E01
0.448,1.645 0.692,1.831 0.244,0.186 10 *a 0.629,1.724 0.955,1.724 false 0.955,1.724 1.844,1.117 false 0.756,3.696 1.000,3.882 0.244,0.186 10 *a 0.945,3.813 1.514,3.813 false 1.514,3.813 1.785,3.678 false 2.72,1.542 2.964,1.728 0.244,0.186 10 *b 2.673,1.647 2.33,1.651 false 2.33,1.651 2.073,0.982 false 0.942,3.082 1.186,3.268 0.244,0.186 10 *b 1.144,3.168 1.471,3.168 false 1.471,3.168 1.645,3.476 false

Install the 2 front stabilizer lower bracket bushes to the front stabilizer bar.

HINT:

Align the protrusions on the bushes with the identification marks on the front stabilizer bar with the protrusions facing inward.


Text in Illustration
*a Protrusion
*b Mark Position


b.
C214684

With the identification marks of the front stabilizer bar facing downwards, support the front stabilizer bar with a jack.

NOTICE:

Place a wooden block between the jack and front stabilizer bar to prevent damage.


HINT:

Place the jack under the center of the vehicle.



c.
C214687E01
1.146,2.914 1.566,3.126 0.420,0.211 10 180° 1.927,2.924 2.323,3.135 0.396,0.211 10 180° 0.659,2.44 0.877,2.610 0.218,0.170 10 *1 2.541,2.422 2.759,2.592 0.218,0.170 10 *2

Install the front stabilizer bar and 2 front stabilizer lower brackets with the 4 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:

Make sure that the protrusions on the front stabilizer lower bracket bushes are positioned within 180° of the stabilizer cylinder and stabilizer link.


Text in Illustration
*1 Stabilizer Link
*2 Stabilizer Cylinder


Hide 6.INSTALL FRONT STABILIZER END BRACKET

a.
C358994

Install the 2 front stabilizer brackets and 2 front stabilizer link bushes with the 4 bolts.

Torque:
75 N*m (765 kgf*cm, 55 ft.*lbf)

HINT:

There are stamps on the front stabilizer brackets to distinguish between the right and left brackets.



Hide 7.INSTALL FRONT SUSPENSION MEMBER BRACE SUB-ASSEMBLY

a.

Install the 2 member braces with the 6 bolts.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 8.BLEED SUSPENSION FLUID

Hide 9.INSTALL FRONT WHEEL

Torque:
for Aluminum Wheel : 103 N*m (1050 kgf*cm, 76 ft.*lbf)
for Steel Wheel : 112 N*m (1137 kgf*cm, 82 ft.*lbf)

Hide 48820B 10.TIGHTEN FRONT STABILIZER LINK ASSEMBLY RH

a.
C214457

Tighten the bolt on the front stabilizer link assembly.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)

NOTICE:

Tighten the bolt with the wheels on the ground.



Hide 48870 11.TIGHTEN FRONT STABILIZER WITH TUBE CYLINDER ASSEMBLY

a.
C214456

Tighten the bolt on the front stabilizer with tube cylinder assembly.

Torque:
130 N*m (1326 kgf*cm, 96 ft.*lbf)

NOTICE:

Tighten the bolt with the wheels on the ground.



Hide 53737B 12.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with the 7 clips.


Hide 51405A 13.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 48826D 15.INSTALL STABILIZER CONTROL VALVE PROTECTOR

Hide 16.INSTALL SIDE STEP ASSEMBLY LH (for 5 Door)

Hide 17.INSPECT VEHICLE HEIGHT