Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2015.06–2017.08
RM27T0E _53 Suspension _053710 TIRE PRESSURE MONITORING _0260907 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2126/26  Transmitter ID not Received in Main Mode  


DESCRIPTION

After all IDs are registered, DTC C2126/26 is stored in the tire pressure warning ECU and receiver and the tire pressure warning light blinks for 1 minute and then illuminates.

When the tire pressure warning ECU and receiver successfully receives radio waves from all the transmitters whose IDs are stored in the ECU, DTC C2126/26 is cleared and the tire pressure warning light goes off.

DTC No. DTC Detection Condition Trouble Area
C2126/26 After ID registration is completed, ECU does not receive radio waves from transmitters whose IDs are stored in ECU.
·

ID registration failure

·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver



NOTICE:

w/ ID Switching Function:

(Main) is displayed on the DTC screen for the DTCs even when the 2nd set of tires is selected.


HINT:

The purpose of this DTC is to help prevent delivering a vehicle that has incorrectly registered IDs. After all IDs are registered, DTC C2126/26 is detected and the tire pressure warning light blinks for 1 minute and then illuminates. If the tire pressure warning light does not turn off after a little while, IDs may be incorrectly registered.


WIRING DIAGRAM

C338972E02
3.219,0.396 4.615,0.802 1.396,0.406 10 false Tire Pressure Warning Valve and Transmitter 0.656,0.906 2.042,1.281 1.385,0.375 10 false Tire Pressure Warning Valve and Transmitter 3.188,1.385 4.563,1.802 1.375,0.417 10 false Tire Pressure Warning Valve and Transmitter 0.656,1.906 2.042,2.302 1.385,0.396 10 false Tire Pressure Warning Valve and Transmitter 3.156,2.458 4.615,2.854 1.458,0.396 10 false Tire Pressure Warning Valve and Transmitter*3 3.063,5.146 4.917,5.396 1.854,0.25 10 false Combination Meter Assembly 0.052,5.427 2.948,5.656 2.896,0.229 10 false Skid Control ECU (Master Cylinder Solenoid) 0.125,8.26 2.156,8.49 2.031,0.229 10 false *1: for Vacuum Brake Booster 2.469,8.229 3.708,8.458 1.24,0.229 10 false *3: w/ Spare Tire 0.125,8.573 3.115,8.802 2.99,0.229 10 false *2: for Hydraulic Brake Booster 6.01,3.563 6.417,3.781 0.406,0.219 10 false SPD 5.75,3.417 5.938,3.635 0.188,0.219 10 false 2 5.052,3.281 5.302,3.5 0.25,0.219 10 false 32 2.729,3.927 2.979,4.146 0.25,0.219 10 false 33 1.979,3.865 2.323,4.229 0.344,0.365 10 false 11*1, 12*2 0.052,4.677 0.896,4.896 0.844,0.219 10 false A6*1 5.031,3.552 5.281,3.771 0.25,0.219 10 false G6 5.031,4.156 5.281,4.375 0.25,0.219 10 false G7 5.031,4.771 5.281,4.99 0.25,0.219 10 false G7 2.688,4.156 2.938,4.375 0.25,0.219 10 false G6 1.594,4.167 1.969,4.385 0.375,0.219 10 false SP1 5.052,3.906 5.302,4.125 0.25,0.219 10 false 16 5.052,4.542 5.302,4.76 0.25,0.219 10 false 17 5.75,4.021 5.938,4.24 0.188,0.219 10 false 5 5.75,4.656 5.938,4.875 0.188,0.219 10 false 9 5.75,6.031 5.938,6.25 0.188,0.219 10 false 3 5.75,7.042 5.938,7.26 0.188,0.219 10 false 7 5.698,7.542 5.938,7.76 0.24,0.219 10 false 12 3.594,6.958 3.781,7.177 0.188,0.219 10 false 1 2.385,6.958 2.573,7.177 0.188,0.219 10 false 2 3.375,6.031 3.646,6.25 0.271,0.219 10 false 13 0.823,6.031 1.094,6.25 0.271,0.219 10 false 4 6.021,4.167 6.427,4.385 0.406,0.219 10 false IND 6.01,4.781 6.583,5 0.573,0.219 10 false GND3 6.01,6.167 6.313,6.385 0.302,0.219 10 false TC 6.01,7.188 6.552,7.406 0.542,0.219 10 false CLSW 6.01,7.667 6.552,7.885 0.542,0.219 10 false GND 3.042,6.146 3.344,6.365 0.302,0.219 10 false TC 1.052,6.177 1.354,6.396 0.302,0.219 10 false CG 1.031,6.552 1.333,6.771 0.302,0.219 10 false G48 2.125,7.573 2.552,7.792 0.427,0.219 10 false G153 5.385,8.177 5.813,8.396 0.427,0.219 10 false R41 1.354,6.552 1.833,6.771 0.479,0.219 10 false DLC3 0.615,8.021 2.073,8.24 1.458,0.219 10 false : Radio Waves 2.552,7.573 3.938,7.927 1.385,0.354 10 false Tire Pressure Warning Reset Switch 5.656,8.167 7.063,8.563 1.406,0.396 10 false Tire Pressure Warning ECU and Receiver 4.646,3.438 4.906,3.656 0.26,0.219 10 false +S 4.521,4.177 4.927,4.396 0.406,0.219 10 false TIRE 3.063,4.021 3.469,4.24 0.406,0.219 10 false SI 4.594,4.771 4.906,4.99 0.313,0.219 10 false EC 0.052,4.854 3.042,5.083 2.99,0.229 10 false Skid Control ECU (Brake Actuator Assembly) 0.063,5.24 0.906,5.458 0.844,0.219 10 false A7*2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.



PROCEDURE

1.IDENTIFY TRANSMITTER NOT RECEIVED
a.

Set the tire pressure to the specified value (See page Suspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION).


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


g.

Check the values by referring to the table below.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 2 Tire Inflation Pressure ID2 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 3 Tire Inflation Pressure ID3 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 4 Tire Inflation Pressure ID4 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 5 Tire Inflation Pressure*2 ID5 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1

HINT:
·

*1: It may take a few minutes until the values are displayed.

·

*2: w/ Spare Tire

·

The wheel position cannot be determined from ID1 through ID4 or ID1 through ID5 (w/ Spare Tire) on the Data List.




h.

Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.


i.

Check the Data List.

NOTICE:
·

It may take a few minutes to display the updated tire pressure data.

·

When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.

·

Record the transmitter ID of which "ID Tire Inflation Pressure" data corresponds to each tire.




j.

After confirming that the "ID Tire Inflation Pressure" data for one tire has changed, repeat this procedure for each tire. Identify the transmitter not received.

Result:
Condition Proceed to
One or more of transmitters abnormal A
All normal B




A

2.CHECK TRANSMITTER ID

B

5.PERFORM INITIALIZATION
2.CHECK TRANSMITTER ID
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check the values by referring to the table below.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Registered ID 1 code Registered ID1 code/
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID1 displayed -
Registered ID 2 code Registered ID2 code/
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID2 displayed -
Registered ID 3 code Registered ID3 code/
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID3 displayed -
Registered ID 4 code Registered ID4 code/
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID4 displayed -
Registered ID 5 code*2 Registered ID5 code/
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID5 displayed -

HINT:
·

*1: Displayed only when the ID No. is not registered.

·

*2: w/ Spare Tire

·

The wheel position cannot be determined from ID1 through ID4 or ID1 through ID5 (w/ Spare Tire) on the Data List.




g.

Check the ID number on the identified transmitter by removing it from the tire and wheel.

C239103E01
0.463,0.163 0.712,0.385 0.249,0.222 10 *1 6.53,0.612 7.019,0.837 0.489,0.225 10 *2 6.123,1.333 6.375,0.682 6.375,0.682 6.501,0.682 false

Text in Illustration
*1 Tire Pressure Warning Valve and Transmitter *2 Transmitter ID (7-digit number)


h.

Confirm that the ID number on the transmitter and the recorded transmitter ID match.

Result:
Result Proceed to
Match A
Do not match B




A

3.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER

B

4.REGISTRATION OF TRANSMITTER ID
3.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
a.

Replace the tire pressure warning valve and transmitter (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING VALVE>REMOVAL).



NEXT

4.REGISTRATION OF TRANSMITTER ID
4.REGISTRATION OF TRANSMITTER ID

NEXT

5.PERFORM INITIALIZATION
5.PERFORM INITIALIZATION

NEXT

6.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
6.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check the values by referring to the table below.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 2 Tire Inflation Pressure ID2 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 3 Tire Inflation Pressure ID3 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 4 Tire Inflation Pressure ID4 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 5 Tire Inflation Pressure*2 ID5 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1

HINT:
·

*1: It may take a few minutes until the values are displayed.

·

*2: w/ Spare Tire

·

When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.

·

The wheel position cannot be determined from ID1 through ID4 or ID1 through ID5 (w/ Spare Tire) on the Data List.

Result:
Result Proceed to
Tire pressure values are not displayed. A
All tire pressure readings are equal to specified values. B






A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

END