Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2015.06–2017.08
RM27T0E _53 Suspension _053710 TIRE PRESSURE MONITORING _0260907 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2174/74  Vehicle Speed Signal Malfunction  C2191/91  Vehicle Speed Signal Error (Test Mode DTC)  


DESCRIPTION

Speeds signals are sent from the combination meter assembly to the tire pressure warning ECU and receiver.

DTC C2191/91 is stored only during the signal check.

DTC Code Detection Condition Trouble Area
C2174/74 All conditions below are met:
·

DTC C2121/21, C2122/22, C2123/23, and/or C2124/24 (C2121/21, C2122/22, C2123/23, C2124/24 and/or C2125/25: w/ Spare Tire) is output

·

Vehicle speed signal malfunction


·

Combination meter

·

Vehicle speed signal circuit

·

Harness or connector

·

Tire pressure warning ECU and receiver

·

Tire pressure warning valve and transmitter


C2191/91 Test mode procedure is performed.
·

Meter / gauge system (speed signal)

·

Vehicle speed signal circuit

·

Harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C296959E06
5.333,1.26 5.615,1.448 0.281,0.188 10 false R41 5.313,1.438 7.021,1.792 1.708,0.354 10 false Tire Pressure Warning ECU and Receiver 5.75,0.927 6.073,1.115 0.323,0.188 10 false SPD 5.75,0.51 6.208,0.698 0.458,0.188 10 false GND3 5.542,0.813 5.708,1.01 0.167,0.198 10 false 2 5.531,0.417 5.698,0.615 0.167,0.198 10 false 9 1.552,0.719 1.771,0.906 0.219,0.188 10 false 32 1.552,0.292 1.771,0.479 0.219,0.188 10 false 17 1.552,1.156 1.76,1.323 0.208,0.167 10 false 33 1.198,1.26 1.427,1.448 0.229,0.188 10 false SI 1.167,0.833 1.438,1 0.271,0.167 10 false +S 1.146,0.521 1.417,0.688 0.271,0.167 10 false EC 1.531,0.938 1.833,1.167 0.302,0.229 10 false G6 1.542,0.521 1.844,0.75 0.302,0.229 10 false G7 1.531,1.375 1.833,1.604 0.302,0.229 10 false G6 0.083,1.906 2.042,2.146 1.958,0.24 10 false Combination Meter Assembly 5.177,1.969 7.073,2.208 1.896,0.24 10 false *1: for Vacuum Brake Booster 5.167,2.24 7.156,2.479 1.99,0.24 10 false *2: for Hydraulic Brake Booster 2.969,1.385 3.365,1.594 0.396,0.208 10 false SP1 2.271,1.969 3.146,2.135 0.875,0.167 10 false A6*1 2.271,2.458 5.021,2.698 2.75,0.24 10 false Skid Control ECU (Master Cylinder Solenoid) 2.208,1.26 2.979,1.417 0.771,0.156 10 false 11*1, 12*2 2.271,2.313 3.146,2.479 0.875,0.167 10 false A7*2 2.281,2.115 5.083,2.354 2.802,0.24 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



HINT:

When the speedometer needle is not moving, first troubleshoot the meter/gauge system (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.READ VALUE USING DATA LIST (VEHICLE SPEED)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check that the values indicated on the GTS and on the combination meter assembly are the same.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed/
min.: 0 km/h (0 mph)
max.: 255 km/h (158 mph)
Actual vehicle speed Speed indicated on combination meter assembly

OK:

Vehicle speed indicated on the GTS indicates the actual speed.




OK

2.CHECK DTC OUTPUT

NG

3.CHECK HARNESS AND CONNECTOR (ECU - COMBINATION METER ASSEMBLY)
2.CHECK DTC OUTPUT

b.

Turn the ignition switch off.


c.

Turn the ignition switch ON.


d.

Perform a driving test.


e.

Check for DTCs (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR).

HINT:

The time required for DTC C2174 to be stored is 20 minutes.


Result
Result Proceed to
DTC C2174 is not output A
DTC C2174 is output B



A

B

6.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
3.CHECK HARNESS AND CONNECTOR (ECU - COMBINATION METER ASSEMBLY)
a.

Disconnect the tire pressure warning ECU and receiver R41 connector.


b.

Disconnect the combination meter assembly G6 connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R41-2 (SPD) - G6-32 (+S) Always Below 1 Ω
R41-2 (SPD) or G6-32 (+S) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)
a.

Disconnect the A6*1 skid control ECU (brake actuator assembly) or A7*2 skid control ECU (master cylinder solenoid) connector.

*1: for Vacuum Brake Booster

*2: for Hydraulic Brake Booster



b.

Disconnect the combination meter assembly G6 connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Vacuum Brake Booster
Tester Connection Condition Specified Condition
A6-11 (SP1) - G6-33 (SI) Always Below 1 Ω
A6-11 (SP1) or G6-33 (SI) - Body ground Always 10 kΩ or higher

for Hydraulic Brake Booster
Tester Connection Condition Specified Condition
A7-12 (SP1) - G6-33 (SI) Always Below 1 Ω
A7-12 (SP1) or G6-33 (SI) - Body ground Always 10 kΩ or higher




OK

5.CHECK DTC OUTPUT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK DTC OUTPUT
a.

Check for DTCs.

HINT:


Result
Result Proceed to
DTC P0500 is not output A
DTC P0500 is output B



A

6.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

6.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Replace the tire pressure warning ECU and receiver (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL).



NEXT

7.PERFORM REGISTRATION OF TRANSMITTER ID
7.PERFORM REGISTRATION OF TRANSMITTER ID

NEXT

8.PERFORM INITIALIZATION
8.PERFORM INITIALIZATION

NEXT

9.CHECK TEST MODE DTC (C2191/91)
9.CHECK TEST MODE DTC (C2191/91)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.


f.

Drive the vehicle at 20 km/h (12 mph) or more for 3 seconds or more to check the vehicle speed signal (C2191/91).

Result
Result Proceed to
DTC C2191 is not cleared A
DTC C2191 is cleared B



A

GO TO DTC C2121/21 TO C2124/24 (C2121/21 to C2125/25: w/ Spare Tire)

B

END