The motor relay supplies power to the pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the pump motor.
If the voltage supplied to the motor relay (BM) is below the DTC detection threshold due to low voltage from the battery or generator, these DTCs may be stored.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C0273 | Either condition is met:
1.
All conditions are met for 0.12 seconds or more. -
The IG1 terminal voltage is between 9.5 and 17.2 V. -
During initial check and ABS or BA is operating. -
The relay contact is open when the relay is on. 2.
Both conditions are met for 0.12 seconds. -
The IG1 terminal voltage is below 9.5 V. -
The relay contact remains open when the relay is on. |
·
ABS NO. 1 fuse ·
Motor relay circuit ·
Brake actuator assembly (Motor relay) |
| C0274 | When the motor relay is off, the motor relay remains closed for 4 seconds or more. | ·
Motor relay circuit ·
Brake actuator assembly (Motor relay) |
| C1361 | Immediately after the ignition switch is turned to ON, the relay contact is closed for 4 seconds when the motor fail-safe relay is off. | ·
ABS NO. 1 fuse ·
Motor fail-safe relay circuit ·
Brake actuator assembly (Motor fail-safe relay) |
When replacing the skid control ECU (brake actuator assembly), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When DTC C1241 is output together with DTC C0273, C0274 and/or C1361, inspect and repair the trouble areas indicated by DTC C1241 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1241).
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Motor Relay | Motor relay | Relay ON / OFF | The operating sound of the motor can be heard. |
Check the operating sound of the motor relay when operating it with the intelligent tester.
| Result | Proceed to |
|---|---|
| Operating sound is not heard | A |
| Operating sound is heard | B |
A
B
Turn the ignition switch off.
Disconnect the A6 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A6-24 (BM) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
OK
NG
Disconnect the A6 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A6-13 (GND2) - Body ground | Always | Below 1 Ω |
OK
NG
This code is stored when a problem is identified in the skid control ECU (brake actuator assembly).
The motor relay is in the skid control ECU (brake actuator assembly).
Therefore, motor relay inspections and motor relay unit inspections cannot be performed. Be sure to check if the DTC is output before replacing the skid control ECU (brake actuator assembly).
Turn the ignition switch off.
Reconnect the skid control ECU (brake actuator assembly) connector.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC not output | A |
| DTC output | B |
If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.
If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harnesses, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.
If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness. The DTCs were probably output due to a bad connection of the connector terminal.
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B