Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260910 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch assembly.

DTC Code DTC Detection Condition Trouble Area
C1425 When the IG1 terminal voltage is between 9.5 and 17.4 V, an open STP terminal circuit continues for 3 seconds or more.
·

STP terminal circuit

·

Stop light control ECU assembly

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C294402E05
1.406,1.5 3.177,1.76 1.771,0.26 10 false Stop Light Switch Assembly 5.292,2.938 6.906,3.344 1.615,0.406 10 false Skid Control ECU (Master Cylinder Solenoid ) 0.802,3.375 1.365,3.688 0.563,0.313 10 false STOP 1.833,3.208 2.969,3.531 1.135,0.323 10 false from Battery 2.74,0.74 3.042,0.969 0.302,0.229 10 false 2 1.563,0.76 1.844,1.031 0.281,0.271 10 false 1 5.365,0.74 5.531,0.99 0.167,0.25 10 false 2 5.594,0.729 6.104,1.01 0.51,0.281 10 false STP 1.417,1.333 1.844,1.552 0.427,0.219 10 false A85 5.302,2.771 5.646,2.969 0.344,0.198 10 false A6 4.198,1.583 5.323,1.979 1.125,0.396 10 false Stop Light Control ECU Assembly 3.667,1.417 4.115,1.646 0.448,0.229 10 false STP 3.854,1.146 4.188,1.375 0.333,0.229 10 false 5 3.667,1.875 4.146,2.104 0.479,0.229 10 false GND 3.854,2.135 4.208,2.396 0.354,0.26 10 false 8 5.771,2.052 6.76,2.448 0.99,0.396 10 false Open Detection Circuit 4.208,1.375 4.635,1.646 0.427,0.271 10 false A54 1.792,0.865 2.135,1.146 0.344,0.281 10 false B 2.563,0.896 2.833,1.167 0.271,0.271 10 false L 2.031,0.604 2.5,0.823 0.469,0.219 10 false GND 2.031,0.333 2.344,0.563 0.313,0.229 10 false 3 0.625,2.135 1.052,2.396 0.427,0.26 10 false A59 0.615,2.323 1.115,2.542 0.5,0.219 10 false Diode 0.177,2.625 0.51,2.875 0.333,0.25 10 false 1 0.167,1.938 0.458,2.167 0.292,0.229 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
a.

Turn the ignition switch off


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch/ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


f.

Check that the stop light switch display observed on the intelligent tester changes according to the brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.




OK

2.RECONFIRM DTC

NG

3.INSPECT STOP LIGHT CONTROL ECU ASSEMBLY
2.RECONFIRM DTC

b.

Start the engine.


c.

Depress the brake pedal several times to test the stop light circuit.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

B

3.INSPECT STOP LIGHT CONTROL ECU ASSEMBLY
a.

Inspect the stop light control ECU assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT CONTROL RELAY>INSPECTION).



OK

4.CHECK TERMINAL VOLTAGE (STP)

NG

REPLACE STOP LIGHT CONTROL ECU ASSEMBLY

4.CHECK TERMINAL VOLTAGE (STP)
a.

Make sure that there is no looseness at the locking parts and connecting parts of the connectors.


b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.
U148258E01
0.07,0.072 0.246,0.263 0.177,0.191 10 *a 0.203,1.026 0.428,1.182 0.224,0.156 10 A6 1.81,0.134 2.293,0.341 0.483,0.207 10 STP 1.31,0.864 1.485,0.218 1.485,0.218 1.751,0.218 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-2 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.RECONFIRM DTC

b.

Start the engine.


c.

Depress the brake pedal several times to test the stop light circuit.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

B