Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260910 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1282  Center Differential Lock Position Switch  


DESCRIPTION

DTC C1282 is stored only in test mode.

DTC Code DTC Detection Condition Trouble Area
C1282 Stored during test mode.
·

Harness or connector

·

Transfer system

·

Brake actuator assembly (Skid control ECU)



WIRING DIAGRAM

C212546E09
0.563,0.854 0.75,1.083 0.188,0.229 10 false IG 1.458,1.25 1.667,1.427 0.208,0.177 10 false P1 1.76,1.25 2.031,1.448 0.271,0.198 10 false 14 1.365,4.042 1.625,4.229 0.26,0.188 10 false 2-4 1.396,4.688 1.646,4.875 0.25,0.188 10 false LO 3.292,3.938 3.604,4.135 0.313,0.198 10 false HI 3.281,4.792 3.573,4.979 0.292,0.188 10 false LO 3.229,5.24 4.854,5.438 1.625,0.198 10 false Transfer Position Switch 3.167,2.156 5.208,2.552 2.042,0.396 10 false Center Differential Lock Detection Switch (Transfer Shift Actuator) 5.188,1.24 5.292,1.396 0.104,0.156 10 false 9 5.438,1.24 5.844,1.448 0.406,0.208 10 false EXI4 5.979,0.635 6.208,0.833 0.229,0.198 10 false IG 5.333,2.438 6.958,2.833 1.625,0.396 10 false Brake Actuator Assembly (Skid Control ECU) 0.135,5.271 2.042,5.521 1.906,0.25 10 false Four Wheel Drive Control ECU 3.167,2.01 3.479,2.177 0.313,0.167 10 false C43 2.51,2.073 2.854,2.25 0.344,0.177 10 false CDL 2.49,2.51 2.854,2.667 0.365,0.156 10 false GND 4.458,4.26 4.781,4.448 0.323,0.188 10 false GND 4.875,4.281 5.021,4.438 0.146,0.156 10 false 4 3.042,3.917 3.177,4.073 0.135,0.156 10 false 5 3.042,4.552 3.167,4.708 0.125,0.156 10 false 2 3.24,5.094 3.542,5.302 0.302,0.208 10 false G18 1.76,4.552 1.99,4.719 0.229,0.167 10 false 13 1.771,3.927 1.969,4.094 0.198,0.167 10 false 11 0.135,5.115 0.427,5.26 0.292,0.146 10 false G53 5.333,2.292 5.563,2.469 0.229,0.177 10 false A6 2.906,1.885 3.021,2.031 0.115,0.146 10 false 9 2.917,2.719 3.135,2.875 0.219,0.156 10 false 10

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


PROCEDURE

1.INSPECT CENTER DIFFERENTIAL LOCK SHIFT
a.

Check that the center differential can shift from free to lock, and from lock to free.

OK:

The center differential can shift from free to lock, and from lock to free.




OK

2.CHECK TEST MODE DTC

NG

3.CHECK TERMINAL VOLTAGE (EXI4)
2.CHECK TEST MODE DTC
a.

Switch the vehicle to test mode, perform the center differential lock signal check, and then check that DTC C1282 is cleared (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).

Result
Result Proceed to
DTC is not cleared A
DTC is cleared B



A

B

3.CHECK TERMINAL VOLTAGE (EXI4)
a.

Set the vehicle in the center differential locked state using the center differential lock switch.


b.

Disconnect the A6 skid control ECU connector.


c.

Turn the ignition switch to ON.


d.
U148255E01
0.279,0.072 0.567,0.270 0.288,0.198 10 *a 2.406,0.102 2.760,0.265 0.354,0.163 10 EXI4 2.384,0.192 2.296,0.192 2.296,0.192 2.156,0.848 false 0.295,1.009 0.503,1.180 0.208,0.172 10 A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-9 (EXI4) - Body ground Center differential locked (Center differential lock switch on) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)


e.

Connect the A6 skid control ECU connector.


f.

Set the vehicle in the center differential free state using the center differential lock switch.


g.

Disconnect the A6 skid control ECU connector.


h.

Turn the ignition switch to ON.


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-9 (EXI4) - Body ground Center differential free (Center differential lock switch off) 11 to 14 V




OK

4.CHECK TEST MODE DTC

NG

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FOUR WHEEL DRIVE CONTROL ECU/TRANSFER SHIFT ACTUATOR)
4.CHECK TEST MODE DTC
a.

Switch the vehicle to test mode, perform the center differential lock signal check, and then check that DTC C1282 is cleared (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).

Result
Result Proceed to
DTC is not cleared A
DTC is cleared B



A

B

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FOUR WHEEL DRIVE CONTROL ECU/TRANSFER SHIFT ACTUATOR)
a.

Disconnect the A6 skid control ECU connector.


b.

Disconnect the G53 four wheel drive control ECU connector.


c.

Disconnect the C43 transfer shift actuator connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A6-9 (EXI4) - G53-14 (P1) Always Below 1 Ω
A6-9 (EXI4) - C43-9 (CDL) Always Below 1 Ω
A6-9 (EXI4) - Body ground Always 10 kΩ or higher



OK

GO TO TRANSFER SYSTEM (PROBLEM SYMPTOMS TABLE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR