Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the hill-start assist control operating signal from the skid control ECU (master cylinder solenoid), the stop light control ECU contact turns on and the stop light comes on.

DTC Code DTC Detection Condition Trouble Area
C1380 Either condition is met:
1.

When the voltage at the IG1 terminal is between 10 and 14 V and the stop light control ECU assembly drive output (STPO) is on, a signal is not input to the STP2 terminal for 5 seconds or more.

2.

When the voltage at the IG1 terminal is between 10 and 14 V and the stop light control ECU assembly drive output (STPO) is off, the signal at the STP terminal is different from the input signal at the STP2 terminal for 5 seconds or more.


·

STOP fuse

·

Stop light switch circuit

·

Stop light control ECU assembly

·

Stop light control ECU circuit

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C294401E05
2.652,3.551 5.258,3.818 2.606,0.267 10 Stop Light Control ECU Assembly 0.635,1.872 1.040,2.047 0.405,0.174 10 STOP 0.99,2.774 1.805,2.957 0.816,0.184 10 from Battery 2.241,1.571 2.384,1.736 0.143,0.165 10 8 2.237,0.581 2.374,0.750 0.137,0.170 10 6 2.453,0.582 2.744,0.752 0.291,0.170 10 +B 2.436,1.569 2.790,1.723 0.354,0.154 10 GND 2.234,2.511 2.349,2.661 0.114,0.151 10 5 2.459,2.51 2.761,2.666 0.302,0.156 10 STP 4.372,1.542 4.698,1.698 0.326,0.156 10 ACC 4.796,1.531 4.909,1.682 0.112,0.151 10 9 4.368,2.933 4.687,3.078 0.319,0.145 10 OUT 4.793,2.935 4.908,3.079 0.115,0.144 10 1 0.665,4.66 2.498,4.867 1.833,0.207 10 Stop Light Switch Assembly 1.788,3.916 1.921,4.085 0.133,0.170 10 2 0.615,3.918 0.736,4.078 0.121,0.161 10 1 3.596,4.429 4.511,4.627 0.915,0.198 10 to Stop Lights 6.149,3.024 6.564,3.212 0.416,0.188 10 STP2 6.149,4.045 6.477,4.211 0.329,0.166 10 STP 5.89,3.925 6.012,4.090 0.122,0.165 10 7 5.83,2.937 6.035,3.088 0.205,0.151 10 45 6.149,1.652 6.547,1.815 0.398,0.163 10 STPO 5.83,1.528 6.035,1.683 0.204,0.156 10 16 5.411,4.897 7.069,5.248 1.658,0.350 10 Skid Control ECU (Master Cylinder Solenoid) 5.411,4.738 5.628,4.896 0.217,0.158 10 A7 2.652,3.388 2.959,3.539 0.306,0.151 10 A54 0.665,4.506 1.050,4.681 0.385,0.174 10 A85 0.9,1.062 1.209,1.218 0.309,0.156 10 A59 0.9,1.268 1.292,1.437 0.392,0.170 10 Diode 1.358,0.56 1.479,0.721 0.121,0.161 10 2 0.728,0.572 0.861,0.742 0.133,0.170 10 1 1.305,3.53 1.438,3.700 0.133,0.170 10 3 0.844,4.047 1.163,4.192 0.319,0.145 10 B 1.104,3.738 1.478,3.884 0.375,0.145 10 GND 1.608,4.04 1.756,4.185 0.148,0.145 10 L

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>C1425).


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off




OK

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)

NG

6.CHECK TERMINAL VOLTAGE AND RESISTANCE (+B, GND)
2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


f.

Check that the stop light switch condition observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.




OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)

NG

9.CHECK TERMINAL VOLTAGE (STP)
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay Stop light control ECU ECU ON/OFF Observe the stop lights (do not come on for 2 to 5 seconds).


f.

While performing the Active Test, check the illumination condition of the stop lights and "Stop Light Relay Output" in the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control ECU output/ ON or OFF ON: Stop light control ECU on (Stop lights on)
OFF: Stop light control ECU off (Stop lights off)
-


Result
Result Proceed to
When Active Test performed, Data List item changes between ON and OFF and stop lights turn on and off A
When Active Test performed, Data List item changes between ON and OFF, but stop lights do not turn on B


A

4.CHECK TERMINAL VOLTAGE (STP2)

B

10.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT CONTROL ECU ASSEMBLY)
4.CHECK TERMINAL VOLTAGE (STP2)
a.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.
U148398E01
1.022,0.617 1.224,0.780 0.202,0.163 10 A7 0.128,0.005 2.553,0.360 2.426,0.354 10 *a 2.539,1.538 2.539,1.873 false 2.346,1.886 2.748,2.049 0.402,0.163 10 STP2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-45 (STP2) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.RECONFIRM DTC

b.

Start the engine.


c.

Perform a road test.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

6.CHECK TERMINAL VOLTAGE AND RESISTANCE (+B, GND)
a.

Disconnect the A54 stop light control ECU assembly connector.


b.
U148288E02
1.26,1.26 0.479,1.448 0.479,1.448 0.479,1.531 false 1.927,1.271 2.917,1.417 2.917,1.417 2.917,1.521 false 0.073,0.031 0.26,0.198 0.188,0.167 10 false *a 0.375,1.531 0.594,1.688 0.219,0.156 10 false +B 2.771,1.573 3.104,1.75 0.333,0.177 10 false GND 0.333,0.885 0.635,1.052 0.302,0.167 10 false A54

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-6 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-8 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control ECU Assembly)



OK

7.CHECK TERMINAL VOLTAGE (STP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TERMINAL VOLTAGE (STP)
a.

Disconnect the A54 stop light control ECU assembly connector.


b.
U148289E01
0.077,0.048 0.266,0.218 0.189,0.170 10 *a 0.375,1.548 0.701,1.707 0.326,0.159 10 STP 1.047,1.242 0.504,1.41 0.504,1.41 0.504,1.496 false 0.48,0.644 0.761,0.807 0.281,0.163 10 A54

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-5 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control ECU Assembly)



OK

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL ECU ASSEMBLY - MASTER CYLINDER SOLENOID)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL ECU ASSEMBLY - MASTER CYLINDER SOLENOID)
a.

Disconnect the A54 stop light control ECU assembly connector.


b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-1 (OUT) - A7-45 (STP2) Always Below 1 Ω
A54-1 (OUT) - Body ground Always 10 kΩ or higher




OK

REPLACE STOP LIGHT CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TERMINAL VOLTAGE (STP)
a.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.
U148399E01
0.31,0.712 0.584,0.874 0.274,0.163 10 A7 0.128,0.038 2.553,0.393 2.426,0.354 10 *a 2.509,0.565 2.859,0.742 0.350,0.177 10 STP 1.684,1.133 2.457,0.677 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

10.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT CONTROL ECU ASSEMBLY)
a.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.

Disconnect the A54 stop light control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-16 (STPO) - A54-9 (ACC) Always Below 1 Ω
A7-16 (STPO) - Body ground Always 10 kΩ or higher




OK

11.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT CONTROL ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT CONTROL ECU ASSEMBLY)
a.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.

Disconnect the A54 stop light control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-45 (STP2) - A54-1 (OUT) Always Below 1 Ω
A7-45 (STP2) - Body ground Always 10 kΩ or higher




OK

REPLACE STOP LIGHT CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR