Refer to DTC C1254 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>C1254).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1256 | The fluid pressure inside the accumulator is below the standard value. | ·
Brake booster with accumulator pump assembly ·
Master cylinder solenoid (Accumulator pressure sensor) ·
Hydraulic brake booster assembly |
When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).
When DTC C1251, C1253, or C1254 is output together with DTC C1256 inspect and repair the trouble area indicated by DTC C1251, C1253, or C1254 first.
Turn the ignition switch off.
Depress the brake pedal 20 times or more.
Turn the ignition switch to ON.
Wait for 99 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is output | A |
| DTC is not output | B |
Excessive brake pedal operation results in abnormal accumulator pressure consumption. This is normal.
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Inspect brake booster pump power supply system function.
Turn the ignition switch off.
Depress the brake pedal 20 times or more to release the pressure in the accumulator.
When the pressure is released, the brake pedal stroke becomes longer.
Check that the brake fluid level is at the MAX level.
Chock the 4 wheels and release the parking brake.
Turn the ignition switch to ON and measure the brake booster pump operating time (the time from when the brake booster pump starts operating until it stops).
20 to 80 seconds
Start the engine after the brake boost pump stops.
Check that the ABS warning light and slip indicator light are not illuminated.
Turn off the engine, and then turn the ignition switch to ON.
Check that the brake boost pump operates and then stops when the brake pedal is depressed 4 or 5 times.
Depress the brake pedal 4 or 5 times and measure the brake booster pump operating time (the time from when the brake booster pump starts operating until it stops).
2 to 11 seconds
Check that the brake warning light illuminates and the buzzer sounds when the brake pedal is fully depressed continuously 15 to 20 times.
Wait 120 seconds or more after turning the ignition switch to ON before performing this inspection.
Check brake booster operation.
Turn the ignition switch off.
Depress the brake pedal 20 times or more to release the pressure in the accumulator.
When the pressure is released, the brake pedal stroke becomes longer.
Depress the brake pedal, start the engine, and check the change in the brake pedal height.
The brake pedal moves slightly inward.
Inspect brake master cylinder fluid pressure change (for LHD: See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>ON-VEHICLE INSPECTION, for RHD: See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>ON-VEHICLE INSPECTION).
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Accumulator Sensor | Accumulator pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V | 3.58 to 5 V | If the value is constant regardless of the pump operation, an accumulator pressure sensor malfunction is suspected. |
Check that the accumulator output value is normal.
Accumulator pressure sensor value is normal.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output (for LHD) | B |
| DTC is output (for RHD) | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Remove the hydraulic brake booster assembly (for LHD: See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>REMOVAL, for RHD: See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>REMOVAL).
Using a screwdriver, remove the 2 screws and pull out the wire harness from the master cylinder solenoid.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Red wire terminal - Black wire terminal | Always | Below 2 Ω |
| *1 | Pump motor wire harness |
| *a | Red wire |
| *b | Black wire |
Install the pump motor wire harness to the master cylinder solenoid with the 2 screws.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D