Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1453  Reservoir Level Switch Disconnected  C1454  Reservoir Level Low  


DESCRIPTION

The brake fluid level warning switch sends the appropriate signal to the skid control ECU when the brake fluid level drops.

DTC Code DTC Detection Condition Trouble Area
C1453 With the ECU terminal IG1 voltage at 10 to 14 V, an open in the brake fluid level warning switch circuit continues for 2 seconds or more.
·

Brake fluid level

·

Brake fluid level warning switch (Brake master cylinder reservoir assembly)

·

Harness or connector

·

Master cylinder solenoid (Skid control ECU)


C1454 The fluid level of the reservoir is below the LOW level for 40 seconds after the ignition switch is turned to ON, or for 7 seconds during pump motor operation.

WIRING DIAGRAM

C336251E02
1.063,0.76 1.219,0.958 0.156,0.198 10 false 1 3.208,0.771 3.365,0.969 0.156,0.198 10 false 2 1.313,0.76 1.667,0.958 0.354,0.198 10 false GND 2.813,0.781 3.094,0.958 0.281,0.177 10 false LBL 4.177,0.781 4.396,0.979 0.219,0.198 10 false 41 4.469,0.906 4.75,1.083 0.281,0.177 10 false LBL 4.458,1.51 4.781,1.698 0.323,0.188 10 false A7 1.26,1.573 1.583,1.76 0.323,0.188 10 false A90 4.458,1.667 6.031,2.052 1.573,0.385 10 false Master Cylinder Solenoid (Skid Control ECU) 1.26,1.74 3.333,2.25 2.073,0.51 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir assembly)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).


PROCEDURE

1.CHECK BRAKE FLUID LEVEL
a.

Turn the ignition switch off.


b.

Depress the brake pedal 40 times or more (until the pedal reaction feels light and pedal stroke becomes longer).


c.

Check the amount of fluid in the brake reservoir.

HINT:

When the ignition switch is turned to ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm (0.197 in.) from the level when the ignition switch is off (normal).


OK:

Brake fluid level is normal.




OK

2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH

NG

CHECK AND REPAIR BRAKE FLUID LEAK

2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
a.

Disconnect the A90 brake fluid level warning switch connector.


b.
C217215E02
0.12,0.094 0.297,0.271 0.177,0.177 10 *a 2.531,1.493 2.909,1.655 0.378,0.163 10 GND 0.503,1.499 0.804,1.690 0.302,0.191 10 LBL 1.409,1.251 0.653,1.366 0.653,1.366 0.653,1.46 false 1.974,1.266 2.668,1.374 2.668,1.374 2.668,1.439 false

Measure the resistance according to the value(s) in the table below.

HINT:

A float is placed inside the reservoir. Its position can be changed by increasing/decreasing the level of brake fluid.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (GND) - 2 (LBL) Float UP (Switch off) 1.9 to 2.1 kΩ
Float DOWN (Switch on) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Brake Fluid Level Warning Switch)

HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

C

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)
a.

Disconnect the A7 skid control ECU connector.


b.

Disconnect the A90 brake fluid level warning switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-41 (LBL) - A90-2 (LBL) Always Below 1 Ω
A7-41 (LBL) - Body ground Always 10 kΩ or higher
A90-1 (GND) - Body ground Always Below 1 Ω




OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine and idle it for approximately 40 seconds.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C