Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C1434  Steering Angle Sensor Output Malfunction  


DESCRIPTION

Steering angle sensor signals are sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering angle sensor zero point malfunction diagnostic function.

DTC Code DTC Detection Condition Trouble Area
C1434 An error in communication between the skid control ECU and the steering angle sensor, or an abnormal steering angle sensor zero point.
·

Steering angle sensor power supply

·

Steering angle sensor (Spiral cable sub-assembly)

·

Brake actuator assembly (Skid control ECU)



CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove the steering sensor from the spiral cable sub-assembly.

·

When replacing the spiral cable sub-assembly, confirm that the replacement part is of the correct specification.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When DTC U0073, U0123, U0124 and/or U0126 is output together with DTC C1434, inspect and repair the trouble areas indicated by DTC U0073, U0123, U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>U0073).

·

When any of the speed sensors or the yaw rate and acceleration sensor has trouble, DTCs for the steering angle sensor may be stored even when the steering angle sensor is normal. When DTCs for the speed sensors or yaw rate and acceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.CHECK DTC

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).


d.

Start the engine.


e.

Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left, and then check that no speed sensor or yaw rate and acceleration sensor DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
No CAN communication system, speed sensor, or yaw rate and acceleration sensor DTCs are output A
CAN communication system DTC is output for LHD without Entry and Start System B
CAN communication system DTC is output for LHD with Entry and Start System C
Speed sensor or yaw rate and acceleration sensor DTC is output D

HINT:
·

If there is a malfunction in any of the speed sensors or the yaw rate and acceleration sensor, an abnormal value may be output although the steering angle sensor is normal.

·

If speed sensor and yaw rate and acceleration sensor DTCs are output simultaneously, repair these two sensors first, and then inspect the steering angle sensor.





A

2.CHECK TERMINAL VOLTAGE (BAT)

B

C

D

2.CHECK TERMINAL VOLTAGE (BAT)

OK

3.CHECK TERMINAL VOLTAGE (IG)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (IG)

OK

4.CHECK HARNESS AND CONNECTOR (ESS CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ESS CIRCUIT)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR