Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR › 2015.06–2020.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260921 BRAKE ACTUATOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL BRAKE ACTUATOR BOLT CUSHION

a.

Install the 3 brake actuator bolt cushions to the brake actuator bracket.


Hide 2.INSTALL BRAKE ACTUATOR CASE COLLAR

a.

Install the 3 brake actuator case collars to the brake actuator bolt cushions.

NOTICE:

Make sure the collars are in full contact with the cushions.



Hide 3.INSTALL BRAKE ACTUATOR BRACKET

a.
C213643E01
1.455,3.128 1.579,3.280 0.125,0.152 10 A 0.241,1.542 0.365,1.695 0.125,0.152 10 B 2.847,2.303 2.971,2.455 0.125,0.152 10 C

Install the brake actuator bracket to the brake actuator with the 3 bolts. Tighten the 3 bolts uniformly in alphabetical order.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator before connecting the 6 brake lines because the brake actuator is filled with brake fluid.

·

Do not hold the actuator by the connector.

·

If the actuator is dropped, replace it.




Hide 4.INSTALL BRAKE ACTUATOR ASSEMBLY

a.
C213642E01
0.359,1.829 0.482,1.978 0.123,0.149 10 A 1.339,3.109 1.462,3.258 0.123,0.149 10 B 2.499,2.614 2.622,2.763 0.123,0.149 10 C

Install the brake actuator with bracket with the 3 nuts. Tighten the 3 nuts uniformly in alphabetical order.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not damage the brake lines or wire harness.

·

Do not hold the actuator by the connector.

·

If the actuator is dropped, replace it.




b.
C213641E02
1.844,1.583 2.344,1.458 2.344,1.458 2.854,1.458 true 1.5,1.74 1.385,1.813 1.385,1.813 1.385,1.927 true 1.698,0.885 1.698,0.406 1.698,0.406 2.198,0.406 true 1.469,0.938 1.469,0.115 1.469,0.115 1.365,0.115 true 1.24,1 1.24,0.271 1.24,0.271 1.042,0.271 true 1.021,1.052 0.594,0.271 0.594,0.271 0.354,0.271 true 2.208,0.344 2.365,0.5 0.156,0.156 10 true *1 0.156,0.198 0.313,0.354 0.156,0.156 10 false *2 0.833,0.198 0.99,0.354 0.156,0.156 10 false *3 1.177,0.031 1.333,0.188 0.156,0.156 10 false *4 2.875,1.375 3.031,1.531 0.156,0.156 10 true *5 1.323,1.958 1.479,2.115 0.156,0.156 10 false *6

Set each brake line in the correct position on the brake actuator as shown in the illustration.

HINT:
·

*1: To front wheel cylinder RH

·

*2: To front wheel cylinder LH

·

*3: To rear wheel cylinder RH

·

*4: To rear wheel cylinder LH

·

*5: From front master cylinder

·

*6: From rear master cylinder




c.
C216423E02
1.521,0.542 1.646,0.698 0.125,0.156 10 false A 1.24,0.604 1.365,0.76 0.125,0.156 10 false A 0.958,0.698 1.083,0.854 0.125,0.156 10 false A 0.635,1.469 0.76,1.646 0.125,0.177 10 true A 1.24,1.958 1.375,2.115 0.135,0.156 10 true B 1.573,1.896 1.708,2.063 0.135,0.167 10 true B

Using a union nut wrench, tighten each brake line.

Torque:
for flare nut A : 15 N*m (155 kgf*cm, 11 ft.*lbf)
for flare nut B : 20 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



d.

Connect the brake actuator connector.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter.




Hide 5.INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 2TR-FE)

Hide 6.INSTALL AIR CLEANER CASE ASSEMBLY (for 5L-E)

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 9.INSPECT BRAKE ACTUATOR WITH INTELLIGENT TESTER

Hide 10. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION