Home › Engine / Hybrid System › 5L-E (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053661 5L-E ENGINE MECHANICAL _0260483 ENGINE ASSEMBLY A

5L-E ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12361 1.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the 2 front engine mounting insulators with the 2 nuts.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 3.REMOVE ENGINE FROM ENGINE STAND

a.

Attach an engine sling device and hang the engine with a chain block.


b.

Lift the engine and remove it from the engine stand.


Hide 4.INSTALL ENGINE ASSEMBLY

a.

Slowly lower the engine into the engine compartment.


b.

Install the engine with the 4 bolts and 4 nuts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
A247325E02
0.948,3.667 0.698,3.49 0.698,3.49 0.563,3.49 true 2.167,3.615 1.917,3.427 1.917,3.427 1.781,3.427 true 1.031,3.927 1.177,4.208 1.177,4.208 1.177,4.302 false 2.323,3.927 2.469,4.208 2.469,4.208 2.469,4.302 true 1.01,2.76 1.26,2.99 0.25,0.229 10 false *a 2.365,2.76 2.656,2.979 0.292,0.219 10 false *b 0.354,3.396 0.573,3.583 0.219,0.188 10 false *1 1.083,4.344 1.281,4.531 0.198,0.188 10 false *2 1.583,3.344 1.792,3.531 0.208,0.188 10 false *1 2.406,4.354 2.625,4.552 0.219,0.198 10 false *2

For RHD vehicles only:

When tightening the nut closer to the rear of the vehicle for the engine mounting bracket on the right side, make sure that the claw (stopper) of the bolt does not protrude past the rear edge of the bracket.


Text in Illustration
*1 Claw (Stopper)
*2 Bracket
*a Correct
*b Incorrect


c.

Remove the 2 bolts and 2 engine hangers.


Hide 11354 5.INSTALL FLYWHEEL HOUSING DUST SEAL

Hide 11355 6.INSTALL REAR END PLATE

a.

Install the rear end plate with the 2 bolts.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 13405 7.INSTALL FLYWHEEL SUB-ASSEMBLY

A058716E05
1.052,0.615 0.656,1.365 0.656,1.365 1.01,0.948 true 0.479,1.406 0.823,1.583 0.344,0.177 10 true SST

a.

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.

Clean the bolts and bolt holes.


c.

Apply adhesive to 2 or 3 threads of each of the bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the flywheel to the crankshaft.


e.

Temporarily install the flywheel with the 8 bolts.


f.
A058717E03
1.656,0.802 1.813,0.969 0.156,0.167 10 true 1 1.385,1.115 1.531,1.281 0.146,0.167 10 true 8 1.927,1.729 2.083,1.896 0.156,0.167 10 true 6 1.552,1.625 1.677,1.792 0.125,0.167 10 true 4 2.25,1.552 2.385,1.719 0.135,0.167 10 true 2 2.333,0.917 2.5,1.094 0.167,0.177 10 true 3 2,0.75 2.146,0.896 0.146,0.146 10 true 5 2.406,1.271 2.573,1.448 0.167,0.177 10 true 7

Tighten the 8 bolts uniformly in several steps in the order shown in the illustration.

Torque:
123 N*m (1249 kgf*cm, 90 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing.



Hide 31250 8.INSTALL CLUTCH DISC ASSEMBLY

Hide 31210 9.INSTALL CLUTCH COVER ASSEMBLY

Hide 12371 10.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the rear engine mounting insulator to the transmission with the 4 bolts.

NOTICE:

Perform this procedure when replacement of the engine mounting insulator is necessary.


Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)


Hide 11.INSTALL MANUAL TRANSMISSION ASSEMBLY

Hide 31470 17.CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

Hide 44320 18.INSTALL VANE PUMP ASSEMBLY

a.

Temporarily install the vane pump with the 2 bolts and nut.


b.
A071326E05
1.604,0.833 1.604,0.323 true 1.469,0.115 1.792,0.281 0.323,0.167 10 true SST

Install the pulley to the pump shaft.


c.

Using SST, hold the pulley and install the nut.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
43 N*m (443 kgf*cm, 31 ft.*lbf)


Hide 23271F 19.CONNECT FUEL HOSE

a.

Connect the 2 fuel hoses.


Hide 87245A 20.CONNECT HEATER WATER HOSE ASSEMBLY

a.

Connect the 2 water hoses.


b.

Install the heater water hose clamp with the bolt.

Torque:
14 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 82715 21.INSTALL WIRING HARNESS CLAMP BRACKET (for LHD)

a.

Install the wiring harness clamp bracket with the bolt.

Torque:
22 N*m (219 kgf*cm, 16 ft.*lbf)


Hide 82121 22.CONNECT ENGINE WIRE

a.

Connect the ECM connector.

i.
A226129E09
2.938,0.469 2.802,0.469 2.802,0.469 2.573,0.792 true 2.417,1.25 2.677,1.729 2.677,1.729 2.896,1.729 true 3,0.375 3.208,0.552 0.208,0.177 10 false *1 2.979,1.635 3.219,1.823 0.24,0.188 10 false *2

Attach the grommet to the wire harness support.

Text in Illustration
*1 Grommet
*2 Wire Harness Support


ii.

Pass the wire harness into the vehicle and install the wire harness support.



b.
A225509E03
0.135,0.083 0.417,0.323 0.281,0.24 12 false *A 0.135,2.542 0.406,2.74 0.271,0.198 12 false *B

Connect the 5 ECM connectors and attach the clamp.

Text in Illustration
*A for LHD
*B for RHD


c.
A225291

for LHD:

Connect the 4 wire harness clamps.


d.
A224629

Attach the 2 clamps and connect the connector.


e.

Attach the 2 claws and install the nut.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


f.

Install the No. 1 relay block cover.


g.
A224626E03
1.708,0.156 1.906,0.344 0.198,0.188 10 true A 1.24,2.365 1.427,2.542 0.188,0.177 10 true B 1.667,3.01 1.844,3.188 0.177,0.177 10 true C

Attach the clamp and install the 3 bolts.

Torque:
for bolt A : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
for bolt B : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
for bolt C : 19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 55550 23.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 88320 25.CONNECT COOLER COMPRESSOR ASSEMBLY

a.
A227544E03
0.597,2.181 0.701,2.330 0.104,0.149 10 1 0.469,1.945 0.576,2.098 0.107,0.152 10 2 0.198,1.06 0.298,1.216 0.100,0.156 10 3 0.443,0.845 0.550,1.003 0.107,0.158 10 4 1.104,0.764 1.208,0.919 0.104,0.156 10 5 1.306,0.574 1.421,0.734 0.114,0.159 10 6 0.288,2.181 0.499,2.344 0.211,0.163 10 (A) 0.185,1.942 0.396,2.105 0.211,0.163 10 (A)

Temporarily install the cooler compressor with the 2 bolts.


b.

Temporarily install the idle pulley bracket with the 4 bolts.


c.

Tighten the 6 bolts in the sequence shown in the illustration.

Torque:
for bolt A : 45 N*m (459 kgf*cm, 33 ft.*lbf)
except bolt A : 25 N*m (250 kgf*cm, 18 ft.*lbf)


d.

Connect the wire harness with the bolt.

Torque:
13 N*m (131 kgf*cm, 9 ft.*lbf)


e.

Connect the cooler compressor connector.


Hide 53293C 31.INSTALL RADIATOR SIDE DEFLECTOR RH

Hide 53294C 32.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 52521 33.INSTALL UPPER FRONT BUMPER RETAINER

Hide 17700 35.INSTALL AIR CLEANER CASE ASSEMBLY

a.

Install the air cleaner case with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17801 36.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 37.INSTALL RESONATOR WITH AIR CLEANER CAP SUB-ASSEMBLY

Hide 53737A 38.INSTALL NO. 1 FRONT FENDER APRON TO FRAME SEAL LH

a.

Install the No. 1 front fender apron to frame seal with the 5 clips.


Hide 53737B 39.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal with the 5 clips.


Hide 53736B 40.INSTALL NO. 1 FRONT FENDER APRON TO FRAME SEAL RH

a.

Install the No. 1 front fender apron to frame seal with the 5 clips.


Hide 53736 41.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal with the 4 clips.


Hide 51450 42.INSTALL REAR ENGINE UNDER COVER ASSEMBLY

a.

Install the rear engine under cover with the 4 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51495 43.INSTALL TRANSMISSION UNDER COVER

a.

Install the transmission under cover with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51405A 44.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.
A224743

Hook the engine under cover to the vehicle body as shown in the illustration.


b.

Install the 4 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 52129B 45.INSTALL FRONT BUMPER COVER LOWER

a.

Install the front bumper cover lower with the 5 bolts and clip.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 53292A 46.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 55781E 47.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Install the cowl top ventilator louver (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).


Hide 53301 48.INSTALL HOOD SUB-ASSEMBLY

a.
A229697

Install the hood with the 8 bolts.

Torque:
for bolt A : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for bolt B : 18 N*m (184 kgf*cm, 13 ft.*lbf)

Text in Illustration
V100135

Bolt A
V100136

Bolt B


b.

Connect the washer nozzle hose.


Hide 53301 49.ADJUST HOOD SUB-ASSEMBLY

Hide 74431 50.INSTALL BATTERY TRAY

Hide 28800 51.INSTALL BATTERY

Hide 74481 52.INSTALL BATTERY HOLD DOWN CLAMP

a.
A224625E03
1.042,0.979 1.219,1.156 0.177,0.177 10 true A

Install the battery hold down clamp with the 2 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Connect the engine wire with the nut labeled A.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 77310A 56.TIGHTEN FUEL TANK CAP ASSEMBLY

Hide 61.ADD MANUAL TRANSMISSION OIL