1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
74481
2.REMOVE BATTERY HOLD DOWN CLAMP
Remove the nut and disconnect the engine wire.
Remove the 2 nuts and battery hold down clamp.
28800
3.REMOVE BATTERY
74431
4.REMOVE BATTERY TRAY
53301
5.REMOVE HOOD SUB-ASSEMBLY
Disconnect the washer nozzle hose.
Remove the 8 bolts and hood.
If the hood support is detached from the ball joint, it become non-reusable. Therefore, do not detach the hood support from the ball joint unless replacing it.
55781E
6.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
Remove the cowl top ventilator louver (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).
53292A
7.REMOVE UPPER RADIATOR SUPPORT SEAL
52129B
8.REMOVE FRONT BUMPER COVER LOWER
Remove the clip, 5 bolts and front bumper cover lower.
51405A
9.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Remove the 4 bolts.
Unhook the engine under cover from the vehicle body as shown in the illustration.
51495
10.REMOVE TRANSMISSION UNDER COVER
Remove the 2 bolts and transmission under cover.
51450
11.REMOVE REAR ENGINE UNDER COVER ASSEMBLY
Remove the 4 bolts and rear engine under cover.
12.DRAIN ENGINE COOLANT
13.DRAIN ENGINE OIL
53736
14.REMOVE FRONT FENDER APRON SEAL RH
Remove the 4 clips and fender apron seal.
53736B
15.REMOVE NO. 1 FRONT FENDER APRON TO FRAME SEAL RH
Remove the 5 clips and frame seal.
53737B
16.REMOVE FRONT FENDER APRON SEAL LH
Remove the 5 clips and fender apron seal.
53737A
17.REMOVE NO. 1 FRONT FENDER APRON TO FRAME SEAL LH
Remove the 5 clips and frame seal.
18.REMOVE RESONATOR WITH AIR CLEANER CAP SUB-ASSEMBLY
17801
19.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17700
20.REMOVE AIR CLEANER CASE ASSEMBLY
Remove the 3 bolts and air cleaner case.
52119A
21.REMOVE FRONT BUMPER COVER
52521
22.REMOVE FRONT UPPER BUMPER RETAINER
53294C
23.REMOVE RADIATOR SIDE DEFLECTOR LH
53293C
24.REMOVE RADIATOR SIDE DEFLECTOR RH
16571C
25.REMOVE NO. 1 RADIATOR HOSE
16572D
26.REMOVE NO. 2 RADIATOR HOSE
16711
27.REMOVE FAN SHROUD
16400
28.REMOVE RADIATOR ASSEMBLY
17130
29.REMOVE INTAKE PIPE ASSEMBLY
88320
30.DISCONNECT COOLER COMPRESSOR ASSEMBLY
Remove the 4 bolts and idle pulley bracket.
Disconnect the connector.
Remove the 3 bolts and disconnect the cooler compressor.
It is not necessary to completely remove the cooler compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.
27020
31.REMOVE GENERATOR ASSEMBLY
55550
32.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
Remove the glove compartment door (See page Vehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL).
82121
33.DISCONNECT ENGINE WIRE
Remove the 3 bolts, detach the clamp and disconnect the engine wire.
Remove the No. 1 relay block cover.
Remove the nut and detach the 2 claws.
Disconnect the connector.
Detach the 2 clamps and disconnect the engine wire.
for LHD:
Detach the 4 clamps.
Detach the grommet from the wire harness support.
| *A | for LHD |
| *B | for RHD |
Detach the 4 claws to remove the wire harness support from the vehicle, and then pull out the ECM connector to remove it from the vehicle.
| *A | for LHD |
| *B | for RHD |
Detach the clamp and disconnect the 5 connectors as shown in the illustration.
| *A | for LHD |
| *B | for RHD |
82715
34.REMOVE WIRING HARNESS CLAMP BRACKET (for LHD)
Remove the bolt and wiring harness clamp bracket.
87245A
35.DISCONNECT HEATER WATER HOSE ASSEMBLY
Remove the bolt and disconnect the heater water hoses.
| *A | for Rear Heater |
77310A
36.LOOSEN FUEL TANK CAP ASSEMBLY
23770B
38.DISCONNECT FUEL HOSE
Disconnect the 2 fuel hoses.
44320
39.DISCONNECT VANE PUMP ASSEMBLY
Using SST, hold the pulley and loosen the nut.
Remove the nut and vane pump pulley from the vane pump shaft.
Remove the 2 bolts and nut and disconnect the vane pump.
Disconnect the vane pump from the vehicle with the hoses connected, and hang it with a rope.
31470
40.REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY
28100
41.REMOVE STARTER ASSEMBLY
15601
42.REMOVE OIL FILTER SUB-ASSEMBLY
17410
43.REMOVE FRONT EXHAUST PIPE ASSEMBLY
37140
44.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
37110
45.REMOVE PROPELLER SHAFT ASSEMBLY
46.REMOVE MANUAL TRANSMISSION ASSEMBLY
Remove the manual transmission (See page Drivetrain>G52F (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSMISSION ASSEMBLY>REMOVAL).
12371
47.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
Perform this procedure when replacement of the engine mounting insulator is necessary.
Remove the 4 bolts and rear engine mounting insulator from the transmission.
31210
48.REMOVE CLUTCH COVER ASSEMBLY
31250
49.REMOVE CLUTCH DISC ASSEMBLY
13405
50.REMOVE FLYWHEEL SUB-ASSEMBLY
Using SST, hold the crankshaft.
Remove the 8 bolts and flywheel.
11355
51.REMOVE REAR END PLATE
Remove the 2 bolts and rear end plate.
11354
52.REMOVE FLYWHEEL HOUSING DUST SEAL
53.INSTALL ENGINE HANGER
Install an engine hanger to each location shown in the illustration.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
| No. 1 Engine Hanger | 12281-54080 |
| No. 2 Engine Hanger | 12282-54070 |
| Bolt (No. 1 Engine Hanger) | 90119-10736 |
| Bolt (No. 2 Engine Hanger) | 91622-61022 |
Install the engine hangers with new bolts.
54.REMOVE ENGINE ASSEMBLY
Attach an engine sling device and hang the engine with a chain block.
Remove the 4 nuts and 4 bolts from the front engine mounting insulator LH and RH.
| *1 | for RH Side |
| *2 | for LH Side |
Remove the engine by operating the engine sling device and chain block.
55.INSTALL ENGINE TO ENGINE STAND
Install the engine to an engine stand with bolts.
Remove engine hanger.
56.REMOVE ENGINE WIRE
Remove the engine wire from the engine.
12361
57.REMOVE FRONT ENGINE MOUNTING INSULATOR
Remove the 2 nuts and 2 front engine mounting insulators.