Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2015.06–2016.08
RM27T0E _51 Engine / Hybrid System _053663 2TR-FE ENGINE MECHANICAL _0260503 ENGINE ASSEMBLY A

2TR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53301 4.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose.


b.
A354930

Remove the 8 bolts and hood sub-assembly.

NOTICE:

If the hood support is detached from the ball joint, it become non-reusable. Therefore, do not detach the hood support from the ball joint unless replacing it.



Hide 55781E 5.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 52129B 6.REMOVE FRONT BUMPER COVER LOWER

a.

Remove the clip, 5 bolts and front bumper cover lower.


Hide 51405A 7.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.
A224743

Remove the 4 bolts.


b.

Unhook the No. 1 engine under cover sub-assembly from the vehicle body as shown in the illustration.


Hide 51495 8.REMOVE TRANSMISSION UNDER COVER

a.

Remove the 2 bolts and transmission under cover.


Hide 51450 9.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

a.

Remove the 4 bolts and rear engine under cover assembly.


Hide 53292A 10.REMOVE UPPER RADIATOR SUPPORT SEAL

a.

Remove the 13 clips and upper radiator support seal.


Hide 13.DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 17705 14.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

a.
A337761

Detach the 3 clamps and disconnect the mass air flow meter connector.


b.
A223921

Detach the 4 clamps.


c.

Loosen the hose clamp and remove the air cleaner cap sub-assembly.


Hide 15.REMOVE AIR CLEANER CASE

a.
A218395

Remove the air cleaner filter element sub-assembly.


b.

Remove the 3 bolts and air cleaner case.


Hide 17341 17.REMOVE NO. 1 AIR INJECTION SYSTEM HOSE

a.
A218385

Remove the hose clamp.

NOTICE:

Do not reuse the hose clamp.



b.

Slide the 2 clips and remove the No. 1 air injection system hose from the air switching valve assembly and air pump assembly.


Hide 16571C 19.REMOVE NO. 1 RADIATOR HOSE

a.

Slide the 2 clips and remove the No. 1 radiator hose from the radiator assembly and cylinder head sub-assembly.


Hide 16572D 20.REMOVE NO. 2 RADIATOR HOSE

a.

Slide the 2 clips and remove the No. 2 radiator hose from the radiator assembly and water inlet.


Hide 22.REMOVE NO. 1 OIL COOLER INLET HOSE AND NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transmission)

Hide 23271F 23.REMOVE FUEL HOSE

a.
A222373

Detach the 2 clamps.



Hide 23273C 24.REMOVE NO. 2 FUEL HOSE

a.
A222374

Detach the clamp.


b.

Slide the 2 clips and remove the No. 2 fuel hose from the fuel pressure regulator and floor pipe.


Hide 23820 25.DISCONNECT PURGE LINE HOSE

a.
A354954

Slide the clip and disconnect the purge line hose from the purge VSV.


Hide 44773F 26.DISCONNECT UNION TO CHECK VALVE HOSE

a.
A264501

Slide the clip and disconnect the union to check valve hose from the brake booster assembly.


Hide 27.DISCONNECT HEATER HOSE

a.
A336847E01
0.08,0.042 0.263,0.201 0.183,0.159 10 *A 0.08,2.339 0.263,2.498 0.183,0.159 10 *B

for Single Air Conditioning System:

Slide the 2 clips and disconnect the 2 heater hoses from the heater core.

Text in Illustration
*A for Single Air Conditioning System
*B for Dual Air Conditioning System


b.

for Dual Air Conditioning System:

Slide the 2 clips and disconnect the 2 heater hoses from the water by-pass pipe and hose.


Hide 44320 28.DISCONNECT VANE PUMP ASSEMBLY

a.
A336846

Remove the bolt and disconnect the pressure feed tube.


b.
A354931

Disconnect the 2 connectors.


c.

Remove the 2 bolts and disconnect the vane pump assembly.

HINT:

It is not necessary to completely remove the vane pump assembly. With the hoses connected to the vane pump assembly, hang the vane pump assembly on the vehicle body with a rope.



Hide 88320 29.DISCONNECT COOLER COMPRESSOR ASSEMBLY

a.
A218390

Remove the bolt and disconnect the suction hose from the engine.


b.
A218389

Disconnect the connector.


c.

Remove the 4 bolts and disconnect the cooler compressor assembly.

HINT:

It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



Hide 53736B 30.REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

Hide 53737A 31.REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL LH

Hide 32.DISCONNECT ENGINE WIRE

a.
A222379

Detach the 3 clamps and disconnect the engine wire from the vehicle RH side.


b.

Disconnect the ECM connector.

i.

ii.
A356066

Detach the clamp and disconnect the 9 connectors.


iii.
A268576

Detach the clamp.


iv.
A264503

Detach the grommet from the wire harness support.


v.
A264504

Detach the 4 claws to remove the wire harness support from the vehicle, and then pull out the ECM connector to remove it from the vehicle.



c.
A218402

Disconnect the connector and detach the clamp.


d.

Remove the nut from the engine room No. 1 relay block.


e.

Detach the 2 clamps and disconnect the wire harness from the engine room No. 1 relay block.


f.
A218399

Detach the 2 clamps.


g.

Remove the bolt and disconnect the ground wire.


h.
A222394

Remove the bolt and bracket from the engine mounting bracket LH.


Hide 32101A 37.REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transmission)

Hide 35030 39.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 33030 40.REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)

Hide 12371 41.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the engine mounting insulator is necessary.


a.

Remove the rear No. 1 engine mounting insulator.



Hide 32101 42.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

Hide 31210 43.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31250 44.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 13405 45.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

Hide 11355 46.REMOVE REAR END PLATE

a.

Detach the flywheel housing dust seal.


b.
A354933

Remove the 2 bolts and rear end plate.


Hide 12281A 47.INSTALL NO. 1 ENGINE HANGER

a.
A354934E01
0.033,0 0.231,0.173 0.198,0.173 10 *a 1.799,0 1.997,0.173 0.198,0.173 10 *b

Install 2 No. 1 engine hangers with 2 bolts as shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

Text in Illustration
*a LH Side
*b RH Side

HINT:
No. 1 Engine Hanger 12281-75050
Bolt 91672-81025



Hide 48.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine assembly with a chain block.

NOTICE:

Pay attention to the angle of the sling device as the engine assembly or engine hanger may be damaged or deformed if the angle is incorrect.



b.
A218401E01
0.105,0.023 0.289,0.199 0.184,0.177 10 *a 0.105,2.412 0.289,2.588 0.184,0.177 10 *b

Remove the 4 bolts and 4 nuts.

Text in Illustration
*a RH Side
*b LH Side


c.

Lift the engine assembly out from the vehicle slowly and carefully.

NOTICE:

Make sure the engine assembly is clear of all wiring, hoses and cables.



Hide 49.INSTALL ENGINE TO ENGINE STAND

a.

Install the engine assembly to an engine stand with bolts.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.




b.

Remove the 2 bolts and 2 No. 1 engine hangers.