Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2015.06–2017.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260954 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2782  Power Source Control ECU Malfunction  


DESCRIPTION

The steering lock ECU activates the steering lock motor with the power from the power management control ECU through the IGE circuit. This prevents the steering from being locked while the vehicle is moving.

If NG (PAST) is displayed for Power Supply Open in the Data List, perform troubleshooting according to the procedures below.

The diagnosis information of the steering lock ECU is transmitted to the intelligent tester via the certification ECU as the steering lock actuator assembly (steering lock ECU) is not connected to the CAN communication system.

DTC Code Detection Condition Trouble Area
B2782 An IGE power supply circuit malfunction.
·

Steering lock actuator assembly (steering lock ECU)

·

Power management control ECU

·

Harness or connector



WIRING DIAGRAM

C199368E11
2.008,0.705 2.155,0.852 0.147,0.147 10 8 1.529,0.787 1.925,0.933 0.396,0.147 10 SLR+ 4.275,0.787 4.671,0.933 0.396,0.147 10 IGE 4.275,1.775 4.649,1.958 0.373,0.184 10 GND 4.058,1.697 4.209,1.881 0.151,0.184 10 1 4.063,0.675 4.215,0.858 0.151,0.184 10 3 4.164,2.563 6.264,2.904 2.100,0.341 10 Steering Lock Actuator Assembly (Steering Lock ECU) 1.07,2.52 3.337,2.662 2.267,0.142 10 Power Management Control ECU 1.076,2.383 1.607,2.553 0.531,0.170 10 G51 4.173,2.383 4.704,2.553 0.531,0.170 10 G35

CAUTION / NOTICE / HINT

HINT:

When the engine switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following steps to wake up the ECU:

With the engine switch off, open the driver door. Then (with the engine switch still off) open and close any door several times at 1.5 second intervals.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

If the steering lock actuator assembly (steering lock ECU) is replaced, with the engine switch off and the shift lever in P (for Automatic Transmission), open and close the driver side door to record the current lock position into the steering lock ECU. If this is not performed, the engine may not start.

·

When replacing the steering lock ECU, registration must be performed. Refer to the Service Bulletin for the registration procedure.



PROCEDURE

1.INSPECT STEERING LOCK ECU
a.
U169946E01
0.119,0.063 0.443,0.312 0.324,0.250 10 *a 0.336,1.912 0.696,2.063 0.360,0.151 10 GND 0.244,1.023 0.548,1.174 0.305,0.151 10 G35 0.78,1.997 0.901,1.997 0.901,1.997 1.128,1.226 false

Disconnect the G35 steering lock ECU connector.


b.

Turn the engine switch off, make sure that the steering lock is unlocked and move the shift lever to P*.

*: for Automatic Transmission



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G35-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Lock ECU)


d.
U169919E02
1.188,1.719 1.406,1.719 1.406,1.719 1.896,1.146 false 2.292,1.135 2.604,1.677 2.604,1.677 2.823,1.677 false 0.813,1.625 1.115,1.813 0.302,0.188 10 false IGE 0.083,0.031 0.479,0.26 0.396,0.229 10 false *a 2.875,1.604 3.24,1.792 0.365,0.188 10 false GND 0.323,0.667 0.646,0.823 0.323,0.156 10 false G35

Reconnect the G35 steering lock ECU connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G35-3 (IGE) - G35-1 (GND) Driver side door opened Below 1 V (Steering lock motor operating)
G35-3 (IGE) - G35-1 (GND) Driver side door opened 11 to 14 V (Steering lock motor not operating)


HINT:

When the steering lock is locked and the engine is switch is turned on (IG), the steering lock motor activates to release the steering lock. The motor operates for 2 to 15 seconds.


Text in Illustration
*a Component with harness connected
(Steering Lock ECU)



OK

2.CLEAR DTC

NG

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - POWER MANAGEMENT CONTROL ECU)
2.CLEAR DTC

b.

Disconnect and reconnect the cable to the negative (-) battery terminal to clear the malfunction history of Power Supply Open.



NEXT

3.READ VALUE USING INTELLIGENT TESTER (POWER SUPPLY OPEN)
3.READ VALUE USING INTELLIGENT TESTER (POWER SUPPLY OPEN)

b.

Use the Data List to check if the steering lock control is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Power Supply Open Open in ECU record/NG (PAST) or OK NG (PAST): Open in ECU
OK: No malfunction
-

Result
Result Proceed to
·

B2782 is not output

·

"OK" is displayed on the tester.


A
·

B2782 is output

·

"NG (PAST)" is displayed on the tester.


for Manual Tilt and Manual Telescopic Steering Column B
for Power Tilt and Power Telescopic Steering Column C



A

B

C

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the G51 power management control ECU connector.


b.

Disconnect the G35 steering lock ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G35-3 (IGE) - G51-8 (SLR+) Always Below 1 Ω
G35-3 (IGE) or G51-8 (SLR+) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR