Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › 2015.06–2017.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260955 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2611  Telescopic Position Sensor or Telescopic Motor Circuit Malfunction  


DESCRIPTION

The telescopic motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column forward and backward. The telescopic position sensor (Hall IC) in the telescopic motor detects the amount that the steering column slides forward or backward and outputs a signal to the multiplex tilt and telescopic ECU based on that sliding amount.

HINT:

The limit positions can be confirmed on the Data List screen of the intelligent tester.

DTC Code Detection Condition Trouble Area
B2611 The telescopic operation stops within the operation range while operating.
·

Harness or connector

·

Telescopic position sensor or telescopic motor

·

Multiplex tilt and telescopic ECU




WIRING DIAGRAM

C358537E01
3.49,0.552 4.01,0.76 0.521,0.208 10 false TI & TE 2.104,0.417 2.896,0.646 0.792,0.229 10 false from Battery 0.75,1.031 1.833,1.25 1.083,0.219 10 false Telescopic Motor 0.479,3.333 1.688,3.688 1.208,0.354 10 false Telescopic Position Sensor 0.667,4.188 1.74,4.396 1.073,0.208 10 false Telescopic Motor 4.573,3.99 6.667,4.167 2.094,0.177 10 false Multiplex Tilt and Telescopic ECU 4.24,3.552 4.604,3.719 0.365,0.167 10 false G116 4.24,0.406 4.604,0.573 0.365,0.167 10 false G116 4.375,0.219 4.51,0.396 0.135,0.177 10 false 2 4.656,0.396 4.896,0.625 0.24,0.229 10 false +B 4.646,0.938 5.073,1.125 0.427,0.188 10 false TEM+ 4.635,1.74 5.063,1.927 0.427,0.188 10 false TEM- 4.635,2.469 5.063,2.656 0.427,0.188 10 false VCE 4.646,2.875 5.073,3.063 0.427,0.188 10 false TES 4.656,3.26 5.083,3.448 0.427,0.188 10 false E2 4.635,3.656 5.063,3.844 0.427,0.188 10 false GND 4.323,3.344 4.51,3.542 0.188,0.198 10 false 11 4.354,3.146 4.542,3.344 0.188,0.198 10 false A 4.344,2.75 4.531,2.948 0.188,0.198 10 false A 4.354,2.365 4.542,2.563 0.188,0.198 10 false A 4.354,1.604 4.542,1.802 0.188,0.198 10 false A 4.354,0.813 4.542,1.01 0.188,0.198 10 false A 4.354,0.615 4.49,0.792 0.135,0.177 10 false 2 4.354,1.396 4.49,1.573 0.135,0.177 10 false 6 4.365,2.167 4.5,2.344 0.135,0.177 10 false 3 4.354,2.563 4.49,2.74 0.135,0.177 10 false 4 4.365,2.958 4.5,3.135 0.135,0.177 10 false 5 6.021,0.531 6.333,0.729 0.313,0.198 10 false +B 5.99,1.333 6.302,1.531 0.313,0.198 10 false +B 6.219,2.167 6.531,2.365 0.313,0.198 10 false 12V 5.958,3.24 6.469,3.427 0.51,0.188 10 false to CPU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TELESCO OPERATION)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the steering column contracts and extends.

Tilt & Telescopic
Tester Display Test Part Control Range Diagnostic Note
Telesco Operation Telescopic operation LONG/SHORT -

Result
Result Proceed to
The steering column does not contract/extend. A
The steering column contracts/extends. B



A

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)

B

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)

OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

OK

4.CHECK TELESCOPIC MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TELESCOPIC MOTOR
a.

Reconnect the G116 multiplex tilt and telescopic ECU connector.


b.

Disconnect the A telescopic motor connector.


c.
U115850E01
0.098,0.026 0.300,0.200 0.202,0.174 10 *a 1.184,0.136 1.478,0.311 0.295,0.174 10 A 0.015,0.825 0.703,0.999 0.688,0.174 10 2 (TEM+) 0.22,1.881 1.052,2.055 0.832,0.174 10 6 (TEM-) 1.094,1.414 0.578,1.881 false 1.094,1.414 0.578,1.881 false 1.089,1.34 0.371,1.02 false

Apply 12 V battery voltage to the telescopic motor connector. Then check the steering column telescopic operation.

OK:
Measurement Condition Specified Condition
12 V battery positive (+) lead → Terminal A-2 (TEM+)
12 V battery negative (-) lead → Terminal A-6 (TEM-)
The steering column contracts.
12 V battery positive (+) lead → Terminal A-6 (TEM-)
12 V battery negative (-) lead → Terminal A-2 (TEM+)
The steering column extends.


Text in Illustration
*a Rear view of wire harness connecter
(to Multiplex Tilt and Telescopic ECU)



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.

Disconnect the G116 multiplex tilt and telescopic ECU connector.


b.
U148221E04
2.01,1.385 1.625,1.719 true 0.229,0.063 0.417,0.26 0.188,0.198 10 false *a 1.24,1.76 1.917,1.958 0.677,0.198 10 false 11 (GND) 2.083,0.229 2.469,0.406 0.385,0.177 10 false G116

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G116-11 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

6.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE TERMINAL VOLTAGE)
a.

Reconnect the G116 multiplex tilt and telescopic ECU connector.


b.
U115804E01
0.231,0.096 0.433,0.270 0.202,0.174 10 *a 1.139,0.453 1.433,0.628 0.295,0.174 10 A 1.538,1.919 2.128,2.094 0.591,0.174 10 3 (VCE) 0.482,1.902 1.063,2.076 0.582,0.174 10 5 (E2) 1.167,1.036 1.001,2.023 false 1.167,1.036 1.001,2.023 false 1.353,1.044 1.464,2.028 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A-3 (VCE) - A-5 (E2) Engine switch on (IG) 8 to 14 V


Text in Illustration
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)



OK

7.CHECK TELESCOPIC POSITION SENSOR

NG

8.CHECK STEERING COLUMN ASSEMBLY
7.CHECK TELESCOPIC POSITION SENSOR
a.
U115805E04
1.156,1.073 0.313,1.49 false 1.25,1.063 1.667,1.979 false 0.229,0.094 0.427,0.271 0.198,0.177 10 false *a 1.156,0.406 1.448,0.563 0.292,0.156 10 false A 0.052,1.542 0.542,1.719 0.49,0.177 10 false 5 (E2) 1.448,1.99 1.979,2.167 0.531,0.177 10 false 4 (TES)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-4 (TES) - A-5 (E2) Telescopic steering contracting or extending Pulse generation
High: 8 to 14 V
Low: Below 1 V


Text in Illustration
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)

8.CHECK STEERING COLUMN ASSEMBLY
a.

Disconnect the A multiplex tilt and telescopic ECU connector.


b.
U116023E01
0.131,0.056 0.333,0.231 0.202,0.174 10 *a 1.159,0.107 1.454,0.281 0.295,0.174 10 A 1.655,1.787 2.246,1.961 0.591,0.174 10 3 (VCE) 1.362,1.516 1.616,1.895 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (VCE) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)