Different voltage values are input to the multiplex tilt and telescopic ECU by operating the tilt and telescopic switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should be moved based on the voltage value.
| DTC Code | Detection Condition | Trouble Area |
|---|---|---|
| B2603 | When operating the tilt and telescopic switch, an abnormal voltage value is input to the multiplex tilt and telescopic ECU. | ·
Harness or connector ·
Tilt and telescopic switch ·
Tilt and telescopic switch circuit ·
Multiplex tilt and telescopic ECU |
Use the Data List to check if the tilt and telescopic switch is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Tilt Up Switch | Input state of tilt up by manual switch/ON or OFF | ON: Tilt up activated by manual switch
OFF: Tilt up not activated by manual switch |
- |
| Tilt Down Switch | Input state of tilt down by manual switch/ON or OFF | ON: Tilt down activated by manual switch
OFF: Tilt down not activated by manual switch |
- |
| Telesco Short Switch | Input state of telescopic short by manual switch/ON or OFF | ON: Telescopic short activated by manual switch
OFF: Telescopic short not activated by manual switch |
- |
| Telesco Long Switch | Input state of telescopic long by manual switch/ON or OFF | ON: Telescopic long activated by manual switch
OFF: Telescopic long not activated by manual switch |
- |
"ON" is displayed on the intelligent tester screen for each switch that is turned on.
"OFF" is displayed on the intelligent tester screen for each switch that is turned off.
OK
NG
Clear the DTCs (See page Steering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Steering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is output | A |
| DTC is not output | B |
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Disconnect the G116 multiplex tilt and telescopic ECU connector.
Disconnect the G44 headlight dimmer switch or G120 windshield wiper switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G116-4 (VC) - G44-8 (VC) | Always | Below 1 Ω |
| G116-3 (MSW) - G44-10 (MSW) | ||
| G44-8 (VC) - Body ground | Always | 10 kΩ or higher |
| G44-10 (MSW) - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G116-4 (VC) - G120-12 (VC) | Always | Below 1 Ω |
| G116-3 (MSW) - G120-13 (MSW) | ||
| G120-12 (VC) - Body ground | Always | 10 kΩ or higher |
| G120-13 (MSW) - Body ground |
OK
NG
Reconnect the G116 multiplex tilt and telescopic ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G116-4 (VC) - G116-3 (MSW) | Engine switch on (IG) | 4.9 to 5.1 V |
| *a | Component with harness connected
(Multiplex Tilt and Telescopic ECU) |
OK
NG
Remove the tilt and telescopic switch (See page Steering>STEERING COLUMN>TILT AND TELESCOPIC MANUAL SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 - 3 | Tilt up | 342 to 378 Ω |
| Tilt down | 1890.5 to 2089.5 Ω | |
| Telescopic contract | 750.5 to 829.5 Ω | |
| Telescopic extend | 152 to 168 Ω |
| Result | Proceed to | |
|---|---|---|
| NG | A | |
| OK | for Headlight Dimmer Switch LH Side Type | B |
| for Headlight Dimmer Switch RH Side Type | C | |
| *a | Component without harness connected
(Tilt and Telescopic Switch) |
A
B
C