Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260968 REAR SEAT ENTERTAINMENT SYSTEM J

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  Mute Signal Circuit between Navigation Receiver Assembly and Television Display Assembly  


DESCRIPTION

This circuit sends a signal to the television display assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the television display assembly is normal, no sound, or only an extremely small sound, can be produced.

WIRING DIAGRAM

E245681E86
0.688,1.719 3.313,1.865 2.625,0.146 10 false Television Display Assembly 1.49,0.906 1.906,1.063 0.417,0.156 10 false MUT1 2,0.813 2.146,0.958 0.146,0.146 10 false 6 4.99,1.688 6.344,2.052 1.354,0.365 10 false Navigation Receiver Assembly 5.26,0.917 5.719,1.073 0.458,0.156 10 false MUTE 5.063,0.771 5.271,0.979 0.208,0.208 10 false 8 0.677,1.531 1.031,1.74 0.354,0.208 10 false W14 4.99,1.51 5.333,1.677 0.344,0.167 10 false H57

PROCEDURE

1.CHECK MUTE SIGNAL CIRCUIT
a.
U149346E02
1.896,0.885 2.135,0.156 2.135,0.156 2.396,0.156 true 2.448,0.063 2.969,0.24 0.521,0.177 10 false MUT1 0.104,0.042 0.323,0.219 0.219,0.177 10 false *a 0.26,0.896 0.646,1.073 0.385,0.177 10 false W14

Remove the television display assembly connector still connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W14-6 (MUT1) - Body ground Television display playing Above 3.5 V
Television display changing modes Below 1 V


Text in Illustration
*a Component with harness connected
(Television Display Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the H57 navigation receiver assembly connector.


b.

Disconnect the W14 television display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H57-8 (MUTE) - W14-6 (MUT1) Always Below 1 Ω
H57-8 (MUTE) - Body ground Always 10 kΩ or higher




OK

3.CHECK TELEVISION DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEVISION DISPLAY ASSEMBLY
a.

Temporarily replace the television display assembly with a new or known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL)


b.

Check that the mute signal circuit functioning normally.

OK:

The mute signal circuit functioning normally.




OK

END (TELEVISION DISPLAY ASSEMBLY WAS DEFECTIVE)

NG