Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Due to this, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E245681E41
1.497,0.912 1.921,1.075 0.424,0.163 10 MUTE 5.252,0.917 5.692,1.080 0.441,0.163 10 MUT1 2.006,0.783 2.185,0.921 0.179,0.139 10 1 5.016,0.787 5.204,0.926 0.188,0.139 10 16 0.893,1.489 1.299,1.645 0.406,0.156 10 H63 5.073,1.48 5.389,1.663 0.316,0.184 10 H51 5.073,1.634 6.342,1.971 1.268,0.336 10 Radio and Display Receiver Assembly 0.893,1.644 2.122,1.980 1.229,0.336 10 Stereo Component Amplifier Assembly

CAUTION / NOTICE / HINT

HINT:

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

1.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
U149404E01
0.207,0.199 0.366,0.362 0.159,0.163 10 *a 1.573,0.882 1.845,1.045 0.272,0.163 10 H63 2.847,1.483 3.277,1.646 0.430,0.163 10 MUTE 2.399,1.818 2.639,1.567 2.639,1.567 2.826,1.567 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H63-1 (MUTE) - Body ground Ignition switch ACC, audio system playing → audio system changing modes 2.0 V or higher → Below 1 V


Text in Illustration
*a Component with harness connected
(Stereo Component Amplifier Assembly)



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H51 radio and display receiver assembly connector.


b.

Disconnect the H63 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H51-16 (MUT1) - H63-1 (MUTE) Always Below 1 Ω
H51-16 (MUT1) - Body ground Always 10 kΩ or higher




OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.
U149434E01
0.086,0.069 0.259,0.233 0.173,0.164 10 *a 1.56,0.582 1.838,0.732 0.278,0.150 10 H51 1.45,2.69 1.869,2.840 0.419,0.150 10 MUT1 0.998,2.095 1.198,2.781 1.198,2.781 1.415,2.781 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H51-16 (MUT1) - Body ground Ignition switch ACC, audio system playing 2.0 V or higher


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY