Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The radio and display receiver assembly and stereo component amplifier assembly are connected by the AVC-LAN communication line.

This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly.

DTC Code DTC Detection Condition Trouble Area
B15D3 When either condition below is met:
·

The stereo component amplifier assembly is/was not connected while the ignition switch is/was turned to ON or ACC

·

Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started


·

Stereo component amplifier assembly power source circuit

·

AVC-LAN circuit between radio and display receiver assembly and stereo component amplifier assembly

·

Stereo component amplifier assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:

For the AVC-LAN communication line, the radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E283655E05
5.625,0.385 5.938,0.583 0.313,0.198 10 false +B 5.635,0.917 5.99,1.083 0.354,0.167 10 false +B2 5.646,1.5 6.063,1.667 0.417,0.167 10 false ACC 5.646,2.135 6.063,2.302 0.417,0.167 10 false TX+ 5.635,2.625 6.052,2.792 0.417,0.167 10 false TX- 5.615,3.115 6.031,3.281 0.417,0.167 10 false GND 5.615,3.615 6.115,3.781 0.5,0.167 10 false GND2 5.229,0.385 5.542,0.583 0.313,0.198 10 false H67 5.292,0.156 5.604,0.354 0.313,0.198 10 false 1 5.271,0.729 5.583,0.927 0.313,0.198 10 false 16 5.271,1.302 5.583,1.5 0.313,0.198 10 false 12 5.302,1.938 5.615,2.135 0.313,0.198 10 false 8 5.292,2.406 5.604,2.604 0.313,0.198 10 false 7 5.292,2.927 5.604,3.125 0.313,0.198 10 false 3 5.25,3.396 5.563,3.594 0.313,0.198 10 false 18 3.208,2.146 3.625,2.313 0.417,0.167 10 false TX1+ 3.25,2.625 3.667,2.792 0.417,0.167 10 false TX1- 2.5,2.979 2.917,3.146 0.417,0.167 10 false H51 2.5,3.167 3.688,3.542 1.188,0.375 10 false Radio and Display Receiver Assembly 2.948,1.104 3.792,1.385 0.844,0.281 10 false AMP 2.771,0.531 3.615,0.813 0.844,0.281 10 false RAD NO.2 2.969,1.688 3.813,1.969 0.844,0.281 10 false ACC 0.615,0.365 1.542,0.646 0.927,0.281 10 false from Battery 0.365,1.51 1.542,1.792 1.177,0.281 10 false from ACC Relay 1.146,4.198 3.656,4.448 2.51,0.25 10 false : AVC-LAN Communication Line 5.469,4.031 6.802,4.448 1.333,0.417 10 false Stereo Component Amplifier Assembly 3.625,1.99 3.938,2.188 0.313,0.198 10 false 7 3.625,2.49 3.938,2.688 0.313,0.198 10 false 8 5.271,0.948 5.583,1.146 0.313,0.198 10 false H67 5.229,1.531 5.542,1.729 0.313,0.198 10 false H63 5.24,2.167 5.552,2.365 0.313,0.198 10 false H63 5.219,2.635 5.531,2.833 0.313,0.198 10 false H63 5.208,3.146 5.521,3.344 0.313,0.198 10 false H67 5.208,3.615 5.521,3.813 0.313,0.198 10 false H67

CAUTION / NOTICE / HINT

NOTICE:
·

If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>B15C3).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check for optional components.

i.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B

HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.






A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CHECK FOR DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.




NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC

OK

END (COMMUNICATION MALFUNCTION DUE TO NOISE)

NG

4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U149472E01
0.06,0.05 0.250,0.227 0.190,0.177 10 *a 1.467,0.278 1.817,0.455 0.350,0.177 10 GND 1.57,1.958 1.868,2.135 0.298,0.177 10 H63 0.201,0.42 0.413,0.598 0.212,0.177 10 +B 1.171,0.854 1.27,0.363 1.27,0.363 1.446,0.363 false 2.891,2.186 3.241,2.363 0.350,0.177 10 ACC 2.486,2.731 2.694,2.271 2.694,2.271 2.87,2.271 false 1.502,1.374 1.944,1.552 0.442,0.177 10 GND2 1.171,1.057 1.304,1.459 1.304,1.459 1.48,1.459 false 0.897,0.871 0.622,0.513 0.622,0.513 0.446,0.513 false 0.201,1.406 0.482,1.584 0.281,0.177 10 +B2 0.915,1.056 0.708,1.499 0.708,1.499 0.532,1.499 false 2.066,0.249 2.364,0.426 0.298,0.177 10 H67

Disconnect the stereo H63 and H67 stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-3 (GND) - Body ground Always Below 1 Ω
H67-18 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H67-1 (+B) - H67-3 (GND) Always 11 to 14 V
H67-16 (+B2) - H67-3 (GND) Always 11 to 14 V
H63-12 (ACC) - H67-3 (GND) Ignition switch ACC 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)


OK

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E221758E22
1.453,0.55 1.657,1.149 false 2.196,0.551 1.794,1.149 false 1.049,0.459 1.374,0.634 0.325,0.174 10 TX1- 2.196,0.459 2.551,0.634 0.355,0.174 10 TX1+

Remove the radio and display receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (TX1-) - 7 (TX1+) Always 60 to 80 Ω




OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H51 radio and display receiver assembly connector.


b.

Disconnect the H67 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H51-7 (TX1+) - H63-8 (TX+) Always Below 1 Ω
H51-8 (TX1-) - H63-7 (TX-) Always Below 1 Ω
H51-7 (TX1+) - Body ground Always 10 kΩ or higher
H51-8 (TX1-) - Body ground Always 10 kΩ or higher




OK

7.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

NG