Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15D5  Rear Seat Entertainment System Disconnected  


DESCRIPTION

The radio and display receiver assembly and television display assembly are connected by the AVC-LAN communication line.

When an AVC-LAN communication error occurs between the radio and display receiver assembly and television display assembly, these DTCs will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D5 When either condition below is met:
·

The television display assembly is/was not connected while the ignition switch is/was turned to ON or ACC.

·

Communication between master unit and the television display assembly is not possible when the engine is started.


·

AVC-LAN communication line

·

Television display assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The radio and display receiver assembly is the master unit.



WIRING DIAGRAM

E286157E01
5.606,0.342 5.859,0.522 0.254,0.180 10 +B 5.409,0.252 5.518,0.431 0.109,0.180 10 1 2.786,0.493 3.526,0.673 0.740,0.180 10 RAD NO.3 0.556,0.35 1.383,0.530 0.828,0.180 10 from Battery 0.336,1.203 1.382,1.383 1.045,0.180 10 from ACC Relay 2.937,1.349 3.292,1.529 0.354,0.180 10 ACC 5.606,1.212 5.917,1.392 0.311,0.180 10 ACC 5.409,1.109 5.518,1.289 0.109,0.180 10 2 5.606,2.116 6.017,2.296 0.411,0.180 10 TX1+ 5.409,1.989 5.518,2.169 0.109,0.180 10 3 5.606,2.6 6.017,2.780 0.411,0.180 10 TX1- 3.153,2.116 3.522,2.296 0.369,0.180 10 TX+ 3.153,2.6 3.522,2.780 0.369,0.180 10 TX- 2.455,2.942 2.824,3.122 0.369,0.180 10 H52 1.138,4.165 3.260,4.345 2.122,0.180 10 : AVC-LAN Communication Line 2.455,3.123 3.745,3.477 1.290,0.354 10 Radio and Display Receiver Assembly 5.464,3.661 6.754,4.015 1.290,0.354 10 Television Display Assembly 3.618,1.98 3.987,2.160 0.369,0.180 10 9 3.618,2.464 3.987,2.644 0.369,0.180 10 10 5.409,2.489 5.518,2.669 0.109,0.180 10 4 5.606,3.105 6.013,3.285 0.407,0.180 10 GND 5.464,3.496 5.904,3.675 0.440,0.180 10 W14

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

2.CHECK CONNECTOR CONNECTION CONDITION
a.

Check that the television display assembly and radio and display receiver assembly connectors are connected properly.

OK:

The connectors are connected properly.




OK

3.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)

NG

CONNECT CONNECTOR CORRECTLY

3.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170602E02
1.083,1.104 0.833,0.729 0.833,0.729 0.688,0.729 false 1.281,1.323 1.448,1.677 1.448,1.677 1.594,1.677 false 0.198,0.094 0.354,0.271 0.156,0.177 10 false *a 1.646,1.604 1.969,1.781 0.323,0.177 10 false GND 0.448,0.667 0.635,0.844 0.188,0.177 10 false +B 0.323,1.104 0.677,1.281 0.354,0.177 10 false W14

Disconnect the television display assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W14-17 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W14-1 (+B) - W14-17 (GND) Always 11 to 14 V
W14-2 (ACC) - W14-17 (GND) Ignition switch off Below 1 V
W14-2 (ACC) - W14-17 (GND) Ignition switch ACC 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Television Display Assembly)


OK

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E221758E24
1.417,1.149 1.214,0.55 1.214,0.55 1.024,0.55 false 1.539,1.149 1.743,0.55 1.743,0.55 1.932,0.55 false 0.676,0.459 0.938,0.634 0.263,0.174 10 TX- 1.97,0.459 2.325,0.634 0.355,0.174 10 TX+

Remove the radio and display receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (TX-) - 10 (TX+) Always 60 to 80 Ω




OK

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the W14 television display assembly connector.


b.

Disconnect the H52 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W14-3 (TX1+) - H52-9 (TX+) Always Below 1 Ω
W14-4 (TX1-) -H52-10 (TX-) Always Below 1 Ω
W14-3 (TX1+) - Body ground Always 10 kΩ or higher
W14-4 (TX1-) - Body ground Always 10 kΩ or higher




OK

6.CHECK TELEVISION DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TELEVISION DISPLAY ASSEMBLY

OK

END (TELEVISION DISPLAY ASSEMBLY IS DEFECTIVE)

NG