1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
63310
3.REMOVE ROOF HEADLINING ASSEMBLY
for 5 Door:
(See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 5 Door)>REMOVAL)
for 3 Door:
(See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 3 Door)>REMOVAL)
86101J
4.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (for 5 Door)
w/o Sliding Roof:
| *A | for Diversity | *B | for Diversity, w/ Digital Audio Broadcasting |
Detach the No. 2 antenna cord sub-assembly from the 6 clamps and the notch on the rear of the roof headlining assembly.
for Diversity:
Detach the No. 2 antenna cord sub-assembly from the 6 clamps and the 2 notches on the rear of the roof headlining assembly.
for Diversity, w/ Digital Audio Broadcasting:
Detach the No. 2 antenna cord sub-assembly from the 7 clamps and the 2 notches on the rear of the roof headlining assembly.
Remove the No. 2 antenna cord sub-assembly from the roof headlining assembly.
Remove the double-sided tape from the roof headlining assembly.
w/ Sliding Roof:
| *A | for Diversity | *B | for Diversity, w/ Digital Audio Broadcasting |
Detach the No. 2 antenna cord sub-assembly from the 11 clamps and the notch on the rear of the roof headlining assembly.
for Diversity:
Detach the No. 2 antenna cord sub-assembly from the 11 clamps and the 2 notches on the rear of the roof headlining assembly.
for Diversity, w/ Digital Audio Broadcasting:
Detach the No. 2 antenna cord sub-assembly from the 12 clamps and the 2 notches on the rear of the roof headlining assembly.
Remove the No. 2 antenna cord sub-assembly from the roof headlining assembly.
Remove the double-sided tape from the roof headlining assembly.
86101J
5.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (for 3 Door)
w/o Sliding Roof:
| *A | for Diversity | *B | for Diversity, w/ Digital Audio Broadcasting |
Detach the No. 2 antenna cord sub-assembly from the clamp and the notch on the rear of the roof headlining assembly.
for Diversity:
Detach the No. 2 antenna cord sub-assembly from the 6 clamps and the 2 notches on the rear of the roof headlining assembly.
for Diversity, w/ Digital Audio Broadcasting:
Detach the No. 2 antenna cord sub-assembly from the 7 clamps and the 2 notches on the rear of the roof headlining assembly.
Remove the No. 2 antenna cord sub-assembly from the roof headlining assembly.
Remove the double-sided tape from the roof headlining assembly.
w/ Sliding Roof:
| *A | for Diversity | *B | for Diversity, w/ Digital Audio Broadcasting |
Detach the No. 2 antenna cord sub-assembly from the 4 clamps and the notch on the rear of the roof headlining assembly.
for Diversity:
Detach the No. 2 antenna cord sub-assembly from the 9 clamps and the 2 notches on the rear of the roof headlining assembly.
for Diversity, w/ Digital Audio Broadcasting:
Detach the No. 2 antenna cord sub-assembly from the 10 clamps and the 2 notches on the rear of the roof headlining assembly.
Remove the No. 2 antenna cord sub-assembly from the roof headlining assembly.
Remove the double-sided tape from the roof headlining assembly.