Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type) › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260991 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Mute Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E280972E17
0.75,1.813 1.667,2.01 0.917,0.198 10 false H63 1.781,0.74 1.938,0.938 0.156,0.198 10 false 1 5.313,0.76 5.719,0.958 0.406,0.198 10 false 16 5.573,0.885 6.115,1.115 0.542,0.229 10 false MUT1 1.271,0.875 1.75,1.094 0.479,0.219 10 false MUTE 5.271,1.792 5.76,2.01 0.49,0.219 10 false H56 5.292,1.948 6.479,2.365 1.188,0.417 10 false Navigation Receiver Assembly 0.74,1.969 2.469,2.292 1.729,0.323 10 false Stereo Component Amplifier Assembly

CAUTION / NOTICE / HINT

HINT:

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

1.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
U149405E01
0.207,0.166 0.366,0.329 0.159,0.163 10 *a 1.599,0.866 1.933,1.029 0.334,0.163 10 H63 2.699,2.413 3.129,2.576 0.430,0.163 10 MUTE 2.399,1.887 2.861,2.381 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H63-1 (MUTE) - Body ground Engine switch on (ACC), audio system playing
→ Changing modes
Above 3.5 V
→ Below 1 V


Text in Illustration
*a Component with harness connected
(Stereo Component Amplifier Assembly)



OK

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H56 navigation receiver assembly connector.


b.

Disconnect the H63 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H56-16 (MUT1) - H63-1 (MUTE) Always Below 1 Ω
H56-16 (MUT1) - Body ground Always 10 kΩ or higher




OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.
U170663E01
1.602,0.69 2.222,0.845 0.620,0.156 10 H56 0.181,0.157 0.336,0.312 0.154,0.156 10 *a 1.054,2.735 1.450,2.890 0.396,0.156 10 MUT1 1.086,2.222 1.371,2.72 false

Disconnect the navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H56-16 (MUT1) - Body ground Engine switch on (ACC), audio system is playing Above 3.5 V


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY