The navigation receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication.
When an AVC-LAN communication error occurs between the navigation receiver assembly and stereo component amplifier assembly, this DTC will be stored.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B15D3 | When either condition below is met:
·
Stereo component amplifier assembly is/was not connected while the engine switch is on (ACC) or on (IG). ·
Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started. |
·
Stereo component amplifier assembly ·
Navigation receiver assembly ·
Harness or connector |
Even if no fault is present, this DTC may be stored depending on the battery condition.
The navigation receiver assembly is the master unit.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).
If DTC B15C3 is output, perform the troubleshooting of DTC B15C3 first.
| Result | Proceed to |
|---|---|
| DTC B15C3 is not output. | A |
| DTC B15C3 is output. | B |
A
B
Check that optional components (including associated wiring) which generate radio waves are not installed.
| Result | Proceed to |
|---|---|
| Optional components (including associated wiring) are installed. | A |
| Optional components (including associated wiring) are not installed. | B |
Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.
A
B
Remove optional components (including associated wiring).
Do not remove optional components or associated wiring without the permission of the customer.
NEXT
Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Navigation Receiver Type)>DTC CHECK / CLEAR).
No DTCs are output.
OK
NG
Disconnect the stereo component amplifier assembly connectors.
| *A | for JBL Made | *B | except JBL Made |
| *a | Front view of wire harness connector
(to Stereo Component Amplifier Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H64-2 (GND) - Body ground | Always | Below 1 Ω |
| H64-6 (GND2) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-3 (GND) - Body ground | Always | Below 1 Ω |
| H67-18 (GND2) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H64-1 (+B) - H64-2 (GND) | Always | 11 to 14 V |
| H64-3 (+B2) - H64-2 (GND) | Always | 11 to 14 V |
| H63-12 (ACC) - H64-2 (GND) | Engine switch on (ACC) | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-1 (+B) - H67-3 (GND) | Always | 11 to 14 V |
| H67-16 (+B2) - H67-3 (GND) | Always | 11 to 14 V |
| H63-12 (ACC) - H67-3 (GND) | Engine switch on (ACC) | 11 to 14 V |
OK
NG
Disconnect the H56 navigation receiver assembly connector.
Disconnect the H63 stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H56-7 (TX1+) - H63-8 (TX+) | Always | Below 1 Ω |
| H56-8 (TX1-) - H63-7 (TX-) | Always | Below 1 Ω |
| H56-7 (TX1+) - Body ground | Always | 10 kΩ or higher |
| H56-8 (TX1-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the stereo component amplifier assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL).
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
OK
NG