Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type) › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260991 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B15D5  Rear Seat Entertainment System Disconnected  


DESCRIPTION

The navigation receiver assembly and television display assembly are connected by the AVC-LAN communication line.

When an AVC-LAN communication error occurs between the navigation receiver assembly and television display assembly, these DTCs will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D5 When either condition below is met:
·

The television display assembly is/was not connected while the engine switch is on (IG or ACC).

·

Communication between master unit and the television display assembly is not possible when the engine is started.


·

AVC-LAN communication line

·

Television display assembly

·

Navigation receiver assembly

·

Harness or connector



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The navigation receiver assembly is the master unit.



WIRING DIAGRAM

E286270E05
5.375,3.844 5.75,4.01 0.375,0.167 10 false W14 5.25,0.49 5.448,0.656 0.198,0.167 10 false 1 5.25,1.25 5.417,1.417 0.167,0.167 10 false 2 2.51,3.271 2.958,3.438 0.448,0.167 10 false H57 2.938,1.552 3.385,1.719 0.448,0.167 10 false ACC 2.771,0.802 3.573,0.969 0.802,0.167 10 false RAD NO. 3 3.708,2.198 3.906,2.365 0.198,0.167 10 false 9 3.708,2.635 3.906,2.802 0.198,0.167 10 false 10 5.25,2.646 5.448,2.813 0.198,0.167 10 false 4 5.25,2.198 5.448,2.365 0.198,0.167 10 false 3 5.458,3.281 5.833,3.448 0.375,0.167 10 false GND 3.25,2.75 3.625,2.917 0.375,0.167 10 false TX- 3.25,2.344 3.625,2.51 0.375,0.167 10 false TX+ 5.458,2.792 5.833,2.958 0.375,0.167 10 false TX1- 5.458,2.375 5.833,2.542 0.375,0.167 10 false TX1+ 5.438,1.385 5.813,1.552 0.375,0.167 10 false ACC 5.438,0.635 5.875,0.802 0.438,0.167 10 false +B 5.177,3.188 5.375,3.354 0.198,0.167 10 false 17 2.51,3.438 3.729,3.844 1.219,0.406 10 false Navigation Receiver Assembly 0.885,4.323 3.51,4.51 2.625,0.188 10 false : AVC-LAN communication Line 5.375,4.021 6.5,4.417 1.125,0.396 10 false Television Display Assembly 0.302,1.396 1.458,1.594 1.156,0.198 10 false from ACC Relay 0.552,0.625 1.708,0.823 1.156,0.198 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

2.CHECK CONNECTOR CONNECTION CONDITION
a.

Check that the television display assembly and navigation receiver assembly connectors are connected properly.

OK:

The connectors are connected properly.




OK

3.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)

NG

CONNECT CONNECTOR CORRECTLY

3.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)
a.
U149263E04
1.083,1.125 0.833,0.75 0.833,0.75 0.688,0.75 true 1.156,1.115 1.344,0.521 1.344,0.521 1.448,0.521 true 1.281,1.313 1.448,1.667 1.448,1.667 1.594,1.667 true 0.198,0.094 0.354,0.271 0.156,0.177 10 false *a 1.625,1.594 2.146,1.771 0.521,0.177 10 false GND 1.51,0.438 1.896,0.615 0.385,0.177 10 false ACC 0.448,0.656 0.635,0.833 0.188,0.177 10 false +B 0.323,1.094 0.677,1.271 0.354,0.177 10 false W14

Disconnect the television display assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W14-17 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W14-1 (+B) - W14-17 (GND) Always 11 to 14 V
W14-2 (ACC) - W14-17 (GND) Engine switch off Below 1 V
W14-2 (ACC) - W14-17 (GND) Engine switch on (ACC) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Television Display Assembly)


OK

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the W14 television display assembly connector.


b.

Disconnect the H57 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W14-3 (TX1+) - H57-9 (TX+) Always Below 1 Ω
W14-4 (TX1-) -H57-10 (TX-) Always Below 1 Ω
W14-3 (TX1+) - Body ground Always 10 kΩ or higher
W14-4 (TX1-) - Body ground Always 10 kΩ or higher




OK

5.CHECK TELEVISION DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TELEVISION DISPLAY ASSEMBLY

OK

END (TELEVISION DISPLAY ASSEMBLY IS DEFECTIVE)

NG