Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260992 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E280972E16
1.229,0.823 2,0.969 0.771,0.146 10 false MUTE 0.677,1.813 1.448,1.958 0.771,0.146 10 false H63 0.688,1.969 2.219,2.344 1.531,0.375 10 false Stereo Component Amplifier Assembly 5.333,1.792 6.104,1.938 0.771,0.146 10 false H51 5.344,1.948 6.656,2.302 1.313,0.354 10 false Radio and Display Receiver Assembly 1.76,0.719 1.906,0.865 0.146,0.146 10 false 1 5.594,0.854 6.365,1 0.771,0.146 10 false MUT1 5.323,0.719 5.552,0.865 0.229,0.146 10 false 16

PROCEDURE

1.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
U149405E01
0.207,0.166 0.366,0.329 0.159,0.163 10 *a 1.599,0.866 1.933,1.029 0.334,0.163 10 H63 2.699,2.413 3.129,2.576 0.430,0.163 10 MUTE 2.399,1.887 2.861,2.381 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H63-1 (MUTE) - Body ground Engine switch on (ACC), audio system playing
→ Changing modes
Above 3.5 V
→ Below 1 V


Text in Illustration
*a Component with harness connected
(Stereo Component Amplifier Assembly)



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H51 radio and display receiver assembly connector.


b.

Disconnect the H63 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H51-16 (MUT1) - H63-1 (MUTE) Always Below 1 Ω
H51-16 (MUT1) - Body ground Always 10 kΩ or higher




OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.
U170664E01
1.602,0.69 2.222,0.845 0.620,0.156 10 H51 0.181,0.157 0.336,0.312 0.154,0.156 10 *a 1.054,2.735 1.450,2.890 0.396,0.156 10 MUT1 1.086,2.222 1.371,2.72 false

Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H51-16 (MUT1) - Body ground Engine switch on (ACC), audio system is playing Above 3.5 V


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY