Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260992 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The radio and display receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication.

When an AVC-LAN communication error occurs between the radio and display receiver assembly and stereo component amplifier assembly, this DTC will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D3 When either condition below is met:
·

Stereo component amplifier assembly is/was not connected while the engine switch is on (ACC) or on (IG).

·

Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started.


·

Stereo component amplifier assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition.

·

The radio and display receiver assembly is the master unit.



WIRING DIAGRAM

E286231E08
3,1.646 3.333,1.792 0.333,0.146 10 false ACC 5.667,1.5 6,1.646 0.333,0.146 10 false ACC 5.667,0.948 6,1.094 0.333,0.146 10 false +B2 5.281,0.917 5.563,1.063 0.281,0.146 10 false H64 5.281,1.49 5.563,1.635 0.281,0.146 10 false H63 5.333,1.292 5.615,1.438 0.281,0.146 10 false 12 5.667,2.167 6,2.313 0.333,0.146 10 false TX+ 5.281,2.146 5.563,2.292 0.281,0.146 10 false H63 5.375,1.958 5.656,2.104 0.281,0.146 10 false 8 3.646,2.417 3.927,2.563 0.281,0.146 10 false 8 5.667,2.552 6,2.698 0.333,0.146 10 false TX- 3.229,2.156 3.583,2.302 0.354,0.146 10 false TX1+ 3.24,2.552 3.594,2.698 0.354,0.146 10 false TX1- 2.521,2.917 2.875,3.063 0.354,0.146 10 false H51 5.281,2.531 5.563,2.677 0.281,0.146 10 false H63 5.375,2.333 5.656,2.479 0.281,0.146 10 false 7 5.667,3.094 6,3.24 0.333,0.146 10 false GND 5.281,3.083 5.563,3.229 0.281,0.146 10 false H64 5.302,2.885 5.583,3.031 0.281,0.146 10 false 2*2 4.917,3.073 5.198,3.219 0.281,0.146 10 false H67 4.938,2.885 5.219,3.031 0.281,0.146 10 false 3*1 3.646,2.031 3.927,2.177 0.281,0.146 10 false 7 4.917,0.938 5.198,1.083 0.281,0.146 10 false H67 5.667,3.646 6.24,3.792 0.573,0.146 10 false GND2 5.104,4.01 6.833,4.354 1.729,0.344 10 false Stereo Component Amplifier Assembly 0.885,4.083 2.896,4.292 2.01,0.208 10 false : AVC-LAN Communication Line 0.177,2.917 2.25,3.271 2.073,0.354 10 false *1: for 3 Door 0.177,3.271 2.25,3.625 2.073,0.354 10 false *2: for 5 Door 2.521,3.083 3.802,3.438 1.281,0.354 10 false Radio and Display Receiver Assembly 5.281,3.625 5.563,3.771 0.281,0.146 10 false H64 5.302,3.427 5.667,3.573 0.365,0.146 10 false 6*2 4.917,3.625 5.198,3.771 0.281,0.146 10 false H67 4.896,3.448 5.229,3.594 0.333,0.146 10 false 18*1 5.313,0.729 5.594,0.875 0.281,0.146 10 false 3*2 4.906,0.74 5.313,0.885 0.406,0.146 10 false 16*1 5.281,0.365 5.563,0.51 0.281,0.146 10 false H64 4.917,0.365 5.198,0.51 0.281,0.146 10 false H67 5.313,0.177 5.594,0.323 0.281,0.146 10 false 1*2 4.948,0.177 5.229,0.323 0.281,0.146 10 false 1*1 5.667,0.365 6,0.51 0.333,0.146 10 false +B 3,1.063 3.333,1.208 0.333,0.146 10 false AMP 2.802,0.51 3.75,0.656 0.948,0.146 10 false RAD NO. 2 0.625,0.333 1.479,0.563 0.854,0.229 10 false from Battery 0.625,0.906 1.438,1.146 0.813,0.24 10 false from Battery 0.365,1.479 1.427,1.698 1.063,0.219 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC
a.

If DTC B15C3 is output, perform the troubleshooting of DTC B15C3 first.

Result
Result Proceed to
DTC B15C3 is not output. A
DTC B15C3 is output. B



A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B

HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK FOR DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.




NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC

OK

END (COMMUNICATION MALFUNCTION DUE TO NOISE)

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the stereo component amplifier assembly connectors.

U170742E02
2.146,1.531 2.354,1.229 2.354,1.229 2.448,1.229 false 3.333,1.385 3.188,0.979 3.188,0.979 3.083,0.979 false 3.844,1.406 3.99,0.979 3.99,0.979 4.104,0.979 false 3.323,1.667 3.188,1.927 3.188,1.927 3.083,1.927 false 3.854,1.656 3.99,1.927 3.99,1.927 4.104,1.927 false 5.146,1.448 5.021,0.802 5.021,0.802 4.906,0.802 false 5.156,1.552 5.021,2.052 5.021,2.052 4.906,2.052 false 5.365,1.448 5.5,0.802 5.5,0.802 5.615,0.802 false 5.365,1.573 5.5,2.052 5.5,2.052 5.615,2.052 false 3.885,0.396 4.083,0.542 0.198,0.146 10 false *A 3.469,0.448 3.75,0.604 0.281,0.156 10 false H64 6.26,0.396 6.458,0.542 0.198,0.146 10 false *B 5.833,0.448 6.115,0.604 0.281,0.156 10 false H67 1.531,0.448 1.813,0.604 0.281,0.156 10 false H63 2.469,1.167 2.875,1.375 0.406,0.208 10 false ACC 0.167,0.104 0.573,0.313 0.406,0.208 10 false *a 2.875,0.906 3.281,1.115 0.406,0.208 10 false +B 4.698,0.75 5.104,0.958 0.406,0.208 10 false +B 4.135,0.927 4.542,1.135 0.406,0.208 10 false GND 5.656,0.719 6.063,0.927 0.406,0.208 10 false GND 5.635,1.99 6.094,2.198 0.458,0.208 10 false GND2 4.135,1.865 4.594,2.073 0.458,0.208 10 false GND2 4.604,2 5.01,2.208 0.406,0.208 10 false +B2 2.771,1.854 3.177,2.063 0.406,0.208 10 false +B2

Text in Illustration
*A for 5 Door *B for 3 Door
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)
- -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5 Door
Tester Connection Condition Specified Condition
H64-2 (GND) - Body ground Always Below 1 Ω
H64-6 (GND2) - Body ground Always Below 1 Ω

for 3 Door
Tester Connection Condition Specified Condition
H67-3 (GND) - Body ground Always Below 1 Ω
H67-18 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 5 Door
Tester Connection Condition Specified Condition
H64-1 (+B) - H64-2 (GND) Always 11 to 14 V
H64-3 (+B2) - H64-2 (GND) Always 11 to 14 V
H63-12 (ACC) - H64-2 (GND) Engine switch on (ACC) 11 to 14 V

for 3 Door
Tester Connection Condition Specified Condition
H67-1 (+B) - H67-3 (GND) Always 11 to 14 V
H67-16 (+B2) - H67-3 (GND) Always 11 to 14 V
H63-12 (ACC) - H67-3 (GND) Engine switch on (ACC) 11 to 14 V




OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H51 radio and display receiver assembly connector.


b.

Disconnect the H63 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H51-7 (TX1+) - H63-8 (TX+) Always Below 1 Ω
H51-8 (TX1-) - H63-7 (TX-) Always Below 1 Ω
H51-7 (TX1+) - Body ground Always 10 kΩ or higher
H51-8 (TX1-) - Body ground Always 10 kΩ or higher




OK

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

NG