Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB1  Short to +B in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a +B short in the blind spot monitor indicator RH.

DTC Code DTC Detection Condition Trouble Area
C1AB1 With the blind spot monitor main switch assembly (multi-function switch) on, the voltage applied to the indicator is high for a certain amount of time even though the blind spot monitor sensor is not outputting voltage to the indicator.
·

Harness or connector

·

Blind spot monitor sensor RH

·

Outer rear view mirror assembly RH

·

Outer rear view mirror sub-assembly RH



WIRING DIAGRAM

E221720E53
3.521,1.219 3.656,1.375 0.135,0.156 10 false 2 5.375,1.24 5.531,1.427 0.156,0.188 10 false 4 3.031,1.219 3.49,1.396 0.458,0.177 10 false BSR+ 5.573,1.354 5.979,1.51 0.406,0.156 10 false OMIR 3.271,1.708 3.406,1.865 0.135,0.156 10 false E 0.75,3.385 1.198,3.542 0.448,0.156 10 false J3 5.406,3.396 5.854,3.552 0.448,0.156 10 false R43 3.51,1.708 3.76,1.917 0.25,0.208 10 false 7 0.823,2.281 3.563,2.479 2.74,0.198 10 false Outer Rear View Mirror Sub-assembly RH 0.74,3.563 3.115,3.74 2.375,0.177 10 false Outer Rear View Mirror Assembly RH 5.406,3.573 6.604,3.885 1.198,0.313 10 false Blind Spot Monitor Sensor RH 0.823,2.49 3.229,2.688 2.406,0.198 10 false (Blind Spot Monitor Indicator RH)

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (multi-function switch) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR RH CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR RH CIRCUIT)
a.

Disconnect the R43 blind spot monitor sensor RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R43-4 (OMIR) - Body ground Engine switch on (IG) Below 1 V




OK

NG

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR ASSEMBLY RH)
3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the R43 blind spot monitor sensor RH connector.


b.

Disconnect the J3 outer rear view mirror assembly RH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R43-4 (OMIR) - Body ground Engine switch on (IG) Below 1 V




OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH)
a.

Disconnect the R43 blind spot monitor sensor RH connector.


b.

Disconnect the outer rear view mirror sub-assembly RH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R43-4 (OMIR) - Body ground Engine switch on (IG) Below 1 V




OK

REPLACE OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH