Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB4  Open in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects an open in the blind spot monitor indicator LH.

DTC Code DTC Detection Condition Trouble Area
C1AB4 With the blind spot monitor main switch assembly (multi-function switch) on, the current flowing to the indicator is below a specified value when indicator operation voltage is sent to the indicator.
·

Harness or connector

·

Outer rear view mirror sub-assembly LH

·

Outer rear view mirror assembly LH

·

Blind spot monitor sensor LH



WIRING DIAGRAM

E221720E57
3.521,1.24 3.656,1.396 0.135,0.156 10 false 2 5.375,1.24 5.542,1.396 0.167,0.156 10 false 4 3.052,1.24 3.458,1.396 0.406,0.156 10 false BSL+ 5.573,1.333 5.979,1.49 0.406,0.156 10 false OMIL 3.323,1.708 3.458,1.854 0.135,0.146 10 false E 0.75,3.396 1.198,3.552 0.448,0.156 10 false K2 5.448,3.396 5.896,3.552 0.448,0.156 10 false R42 3.521,1.719 3.76,1.896 0.24,0.177 10 false 7 0.802,2.313 3.406,2.531 2.604,0.219 10 false Outer Rear View Mirror Sub-assembly LH 0.74,3.563 3.115,3.74 2.375,0.177 10 false Outer Rear View Mirror Assembly LH 5.448,3.573 6.635,3.99 1.188,0.417 10 false Blind Spot Monitor Sensor LH 0.813,2.51 3.219,2.708 2.406,0.198 10 false (Blind Spot Monitor Indicator LH)

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (multi-function switch) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH AND BODY GROUND)
a.

Disconnect the R42 blind spot monitor sensor LH connector.


b.

Disconnect the K2 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R42-4 (OMIL) - K2-2 (BSL+) Always Below 1 Ω
K2-2 (BSL+) - Body ground Always Below 1 Ω




OK

3.CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH
a.

Replace the outer rear view mirror sub-assembly LH with a new or normally functioning one (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH IS DEFECTIVE)

NG

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Replace the outer rear view mirror assembly LH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (OUTER REAR VIEW MIRROR ASSEMBLY LH IS DEFECTIVE)

NG