Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB5  Open in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects an open in the blind spot monitor indicator RH.

DTC Code DTC Detection Condition Trouble Area
C1AB5 With the blind spot monitor main switch assembly (multi-function switch) on, the current flowing to the indicator is below a specified value when indicator operation voltage is sent to the indicator.
·

Harness or connector

·

Outer rear view mirror sub-assembly RH

·

Outer rear view mirror assembly RH

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E221720E58
3.521,1.219 3.656,1.375 0.135,0.156 10 false 2 5.375,1.24 5.531,1.427 0.156,0.188 10 false 4 3.031,1.219 3.49,1.396 0.458,0.177 10 false BSR+ 5.573,1.354 5.979,1.51 0.406,0.156 10 false OMIR 3.271,1.708 3.406,1.865 0.135,0.156 10 false E 0.75,3.385 1.198,3.542 0.448,0.156 10 false J3 5.406,3.396 5.854,3.552 0.448,0.156 10 false R43 3.51,1.708 3.76,1.917 0.25,0.208 10 false 7 0.823,2.281 3.563,2.479 2.74,0.198 10 false Outer Rear View Mirror Sub-assembly RH 0.74,3.563 3.115,3.74 2.375,0.177 10 false Outer Rear View Mirror Assembly RH 5.406,3.573 6.604,3.885 1.198,0.313 10 false Blind Spot Monitor Sensor RH 0.823,2.49 3.229,2.688 2.406,0.198 10 false (Blind Spot Monitor Indicator RH)

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (multi-function switch) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH AND BODY GROUND)
a.

Disconnect the R43 blind spot monitor sensor RH connector.


b.

Disconnect the J3 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R43-4 (OMIR) - J3-2 (BSR+) Always Below 1 Ω
J3-2 (BSR+) - Body ground Always Below 1 Ω




OK

3.CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH
a.

Replace the outer rear view mirror sub-assembly RH with a new or normally functioning one (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH IS DEFECTIVE)

NG

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Replace the outer rear view mirror assembly RH with a new or normally functioning one (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (OUTER REAR VIEW MIRROR ASSEMBLY RH IS DEFECTIVE)

NG