Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  U0232  Lost Communication with Blind Spot Monitor Slave Module  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH judges that there is a communication problem with the blind spot monitor sensor RH.

DTC Code DTC Detection Condition Trouble Area
U0232 The blind spot monitor sensor LH cannot receive signals from the blind spot monitor sensor RH.
·

CAN communication Line

·

Harness or connector

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E233765E68
3.063,1.219 3.375,1.396 0.313,0.177 10 false BRB 2.875,1.115 2.99,1.292 0.115,0.177 10 false 5 2.813,2.51 2.99,2.688 0.177,0.177 10 false 10 3.063,2.615 3.49,2.771 0.427,0.156 10 false BRGD 1.979,1.385 2.229,1.604 0.25,0.219 10 false IG1 0.146,1.219 0.979,1.563 0.833,0.344 10 false from IG NO.1 Relay 3.031,3.208 3.406,3.417 0.375,0.208 10 false R43 3.031,3.406 4.281,3.813 1.25,0.406 10 false Blind Spot Monitor Sensor RH 5.417,3.229 5.771,3.438 0.354,0.208 10 false R42 5.417,3.406 6.594,3.823 1.177,0.417 10 false Blind Spot Monitor Sensor LH 3.531,1.594 3.927,1.771 0.396,0.177 10 false CA2P 3.531,1.938 3.927,2.115 0.396,0.177 10 false CA2N 4.01,1.438 4.125,1.615 0.115,0.177 10 false 1 4.01,1.771 4.125,1.948 0.115,0.177 10 false 6 5.198,1.438 5.313,1.615 0.115,0.177 10 false 1 5.208,1.781 5.323,1.958 0.115,0.177 10 false 6 5.385,1.583 5.781,1.76 0.396,0.177 10 false CA2P 5.385,1.938 5.781,2.115 0.396,0.177 10 false CA2N 0.875,4.021 3.156,4.198 2.281,0.177 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor main switch assembly (multi-function switch) is on.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BLIND SPOT MONITOR SENSOR RH)
a.

Disconnect the R42 blind spot monitor sensor LH connector.


b.

Disconnect the R43 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R42-1 (CA2P) - R43-1 (CA2P) Always Below 1 Ω
R42-6 (CA2N) - R43-6 (CA2N) Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN LINE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BATTERY AND BODY GROUND)
a.
U149433E03
2,1.125 2.365,0.677 2.365,0.677 2.604,0.677 true 2.01,1.396 2.375,1.938 2.375,1.938 2.615,1.938 true 1.583,0.292 1.885,0.49 0.302,0.198 10 false R43 2.656,0.594 3.073,0.75 0.417,0.156 10 false BRB 0.031,0 0.302,0.198 0.271,0.198 10 false *a 2.646,1.854 3.063,2.01 0.417,0.156 10 false BRGD

Disconnect the blind spot monitor sensor RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R43-5 (BRB) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R43-10 (BRGD) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


OK

3.CHECK BLIND SPOT MONITOR SENSOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK BLIND SPOT MONITOR SENSOR RH
a.

Replace the blind spot monitor sensor RH with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (BLIND SPOT MONITOR SENSOR RH IS DEFECTIVE)

NG