Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261015 PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System) C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)  C1612  IG Voltage is Low or High  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that the voltage received by terminal IG is low or high.

DTC Code DTC Detection Condition Trouble Area
C1612
·

IG voltage is low

·

IG voltage is high


·

Harness or connector

·

Parking assist ECU



WIRING DIAGRAM

E348792E01
4.792,2.073 6.073,2.313 1.281,0.24 10 false Parking Assist ECU 4.792,1.896 5.021,2.094 0.229,0.198 10 false I6 4.906,1.354 5.323,1.531 0.417,0.177 10 false GND1 4.698,1.219 4.927,1.396 0.229,0.177 10 false 4 4.708,0.5 4.938,0.677 0.229,0.177 10 false 8 4.896,0.625 5.313,0.802 0.417,0.177 10 false IG 2.365,0.802 3.26,1.01 0.896,0.208 10 false ECU-IG NO.2 0.271,0.635 1.656,0.885 1.385,0.25 10 false from IG1 NO.1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>DTC CHECK / CLEAR).

OK:

DTC C1612 is not output.


HINT:

If the parking assist ECU cannot read the stored information when it is activated, allowing the ECU to store the information again may return the system to normal.




OK

NG

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
U149415E04
2.5,0.938 2.667,0.5 2.667,0.5 2.917,0.5 true 1.292,1.344 1.167,1.833 1.167,1.833 0.917,1.833 true 1.635,0.292 1.917,0.458 0.281,0.167 10 false I6 2.969,0.406 3.375,0.573 0.406,0.167 10 false GND1 0.74,1.75 0.948,1.917 0.208,0.167 10 false IG 0.021,0 0.271,0.188 0.25,0.188 10 false *a

Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I6-4 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I6-8 (IG) - I6-4 (GND1) Engine switch on (IG) 10 to 16 V



Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)

Result
Proceed to Result
OK (for LHD) A
OK (for RHD) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR