This DTC is stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and the rear television camera assembly are not normal.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1622 | An open or short in the rear television camera signal circuit | ·
Harness or connector ·
Rear television camera assembly ·
Parking assist ECU |
When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>INITIALIZATION).
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>CALIBRATION).
Disconnect the I7 parking assist ECU connector.
Disconnect the X9*1 or v2*2 rear television camera assembly connector.
*1: w/ Tire Carrier
*2: w/o Tire Carrier
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-38 (CV-) - X9-2 (CV-) | Always | Below 1 Ω |
| I7-15 (CV+) - X9-3 (CV+) | Always | Below 1 Ω |
| I7-14 (CB+) - X9-6 (CB+) | Always | Below 1 Ω |
| I7-37 (CGND) - X9-5 (CGND) | Always | Below 1 Ω |
| I7-38 (CV-) - Body ground | Always | 10 kΩ or higher |
| I7-15 (CV+) - Body ground | Always | 10 kΩ or higher |
| I7-14 (CB+) - Body ground | Always | 10 kΩ or higher |
| I7-37 (CGND) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-38 (CV-) - v2-2 (CV-) | Always | Below 1 Ω |
| I7-15 (CV+) - v2-3 (CV+) | Always | Below 1 Ω |
| I7-14 (CB+) - v2-6 (CB+) | Always | Below 1 Ω |
| I7-37 (CGND) - v2-5 (CGND) | Always | Below 1 Ω |
| I7-38 (CV-) - Body ground | Always | 10 kΩ or higher |
| I7-15 (CV+) - Body ground | Always | 10 kΩ or higher |
| I7-14 (CB+) - Body ground | Always | 10 kΩ or higher |
| I7-37 (CGND) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the I7 parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-37 (CGND) - Body ground | Always | Below 1 Ω |
| I7-38 (CV-) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I7-14 (CB+) - Body ground | Engine switch on (IG) | 5.5 to 7.05 V |
| *a | Component with harness connected
(Parking Assist ECU) |
| Proceed to | Result |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform A |
| *c | Waveform B | *d | Synchronized Signal |
| *e | Video Waveform | - | - |
Check the waveform of the rear television camera assembly using an oscilloscope.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
The video waveform changes according to the image sent by the rear television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | I7-15 (CV+) - I7-37 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | ·
Waveform A: Engine switch on (IG), camera lens is not covered, displaying an image ·
Waveform B: Engine switch on (IG), camera lens is covered, blacking out the screen |
Waveform is as shown in the illustration.
| Proceed to | Result |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (w/ Tire Carrier) | C |
| NG (w/o Tire Carrier) | D |
A
B
C
D