Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261015 PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System) J

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)  Guide Lines and Buttons are not Displayed for All Display Modes  


DESCRIPTION

The parking assist ECU receives back door courtesy light switch assembly open/close signals from the main body ECU via CAN communication. When the back door is open, the camera aiming cannot be adjusted correctly because the rear television camera assembly is installed on the back door. Therefore, when adjusting the camera aiming calibration while the back door is open, a back door open warning message will be displayed on the screen and camera aiming adjustment will be canceled.

HINT:

The back door courtesy light switch assembly is connected to the main body ECU by the vehicle wire harness.


WIRING DIAGRAM

E198737E18
3.094,1.531 4.75,1.906 1.656,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 3.115,1.365 3.635,1.531 0.521,0.167 10 false G54 0.854,1.375 2.458,1.76 1.604,0.385 10 false Back Door Courtesy Light Switch Assembly 0.854,1.198 1.375,1.365 0.521,0.167 10 false R9 0.771,2.458 2.667,2.667 1.896,0.208 10 false : CAN Communication Line 2.115,0.646 2.271,0.813 0.156,0.167 10 false 1 3.167,0.75 3.573,0.917 0.406,0.167 10 false BCTY 2.906,0.646 3.083,0.813 0.177,0.167 10 false 19 5.542,1.396 6.792,1.76 1.25,0.365 10 false Parking Assist ECU

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the navigation receiver assembly*1 or radio and display receiver assembly*2 after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>CALIBRATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>CALIBRATION).



*1: for Navigation Receiver Type

*2: for Radio and Display Type


PROCEDURE

1.READ VALUE USING GTS (BACK DOOR COURTESY SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Check the Data List for proper functioning of the following item.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Courtesy SW Back door courtesy switch signal/ON or OFF ON: Back door open
OFF: Back door closed
-

OK:

The back door courtesy switch functions as specified in the normal condition column.




OK

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BACK DOOR COURTESY LIGHT SWITCH)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BACK DOOR COURTESY LIGHT SWITCH)
a.

Disconnect the G54 main body ECU connector.


b.

Disconnect the R9 back door courtesy light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-19 (BCTY) - R9-1 Always Below 1 Ω
G54-19 (BCTY) - Body ground Always 10 kΩ or higher




OK

3.INSPECT BACK DOOR COURTESY LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT BACK DOOR COURTESY LIGHT SWITCH ASSEMBLY
a.

Remove the back door courtesy light switch assembly (See page Vehicle Interior>LIGHTING (INT)>BACK DOOR COURTESY SWITCH>REMOVAL).


b.

Inspect the back door courtesy light switch assembly (See page Vehicle Interior>LIGHTING (INT)>BACK DOOR COURTESY SWITCH>INSPECTION).



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE BACK DOOR COURTESY LIGHT SWITCH ASSEMBLY