Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261016 PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) D

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)  CALIBRATION  


ADJUST PARKING ASSIST MONITOR SYSTEM


a.

The parking assist monitor system can be adjusted using diagnostic mode.


b.

If the following operations are performed, it is necessary to perform adjustments and checks using diagnostic mode.

Part Name Operation Adjustment Item Proceed to
Spiral with sensor cable sub-assembly
·

Replacement

·

Removal and installation of the spiral with sensor cable sub-assembly

·

Removal and installation of the connector of the spiral with sensor cable sub-assembly


Steering angle neutral point (Initialize parking assist monitor system) (Click here)
Steering angle setting Procedure 1
Suspension, tires, etc. Replacement (The vehicle height changes due to suspension or tire replacement) Rear television camera assembly optical axis (Back camera position setting) Procedure 1
Rear television camera assembly Replacement Parking assist monitor system initialization Procedure 1
Removal and installation of the rear television camera assembly etc. (Installation angle of the rear television camera assembly changes due to removal and installation) Rear television camera assembly optical axis (Back camera position setting) Procedure 1

HINT:

The adjustment values stored while performing parking assist monitor system calibration are stored in the rear television camera assembly.




PARKING ASSIST MONITOR SYSTEM INITIALIZATION (PROCEDURE 1)


HINT:
·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



a.

Preparation for adjustment

i.

Park the vehicle with the steering wheel centered.


ii.
E271224E01
2.085,0.126 2.288,0.275 0.203,0.149 10 *1 2.401,0.469 2.604,0.619 0.203,0.149 10 *2 3.176,0.9 3.379,1.049 0.203,0.149 10 *4 3.09,1.776 3.293,1.925 0.203,0.149 10 *9 2.686,2.421 2.889,2.570 0.203,0.149 10 *8 1.655,3.074 1.858,3.223 0.203,0.149 10 *7 0.615,2.378 0.818,2.527 0.203,0.149 10 *6 0.916,2.094 1.119,2.243 0.203,0.149 10 *5 0.332,0.47 0.535,0.619 0.203,0.149 10 *3 1.709,0.411 1.915,0.204 1.915,0.204 2.027,0.204 false 2.031,0.75 2.237,0.544 2.237,0.544 2.349,0.544 false 1.202,2.731 0.94,2.469 0.94,2.469 0.832,2.469 false

Set a target bar behind the vehicle for optical axis adjustment of the rear television camera assembly (back camera position setting).

HINT:

Create a target bar for adjustment only when adjusting the optical axis of the rear television camera assembly.


Dimension:
Area Specification
A 824 mm (2.7 ft.) (w/ Tire Carrier)
995 mm (3.26 ft.) (w/o Tire Carrier)
B 4857 mm (15.94 ft.)


Text in Illustration
*1 Vehicle Center
*2 Vehicle
*3 Front
*4 Center of Front Tire
*5 Rear Bumper
*6 Target Bar for Back Camera Adjustment
*7 2000 mm
*8 A
*9 B

HINT:
·

Set a piece of tape on the ground as the target bar for adjustment. Its width and length should be 20 to 30 mm (0.79 to 1.18 in.) and 1995 to 2005 mm (6.54 to 6.58 ft.), respectively. Check the color on the multi-display and choose a tape color which can be easily seen.

·

Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.

·

Check that the back door is fully closed.





b.

Start diagnostic mode.


NOTICE:

The following must be carried out with the engine started. Apply the parking brake, depress the brake pedal, check that the shift lever is in P, and ensure that the vehicle is not moving.


i.
E273700

Select "Function Check/Setting" on the "Service Menu" screen.


ii.
E288889

Select "Camera Setting" on the "Function Check/Setting I" screen.


iii.
E286093

Select "Next" on the "Car Signal Check" screen.

HINT:
·

When "CHK" (red) is displayed for any items on the "Car Signal Check" screen, selecting "Next" will not change the screen to the "Steering Angle Setting" screen.

·

When "CHK" (red) is displayed for any items on the "Car Signal Check" screen, perform inspections using the "Car Signal Check" screen (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>DIAGNOSIS SYSTEM).





c.

Steering Angle Setting

i.
E326704

Check that the steering wheel is centered (approximately +/- 5 degrees or less) and then select "STEERING CENTER MEMORIZE".


ii.

After performing the steering center memorize operation, turn the steering wheel to the left and right lock positions and select "MAX STEERING ANGLE MEMORIZE". The maximum steering angle is then stored and the screen changes to the "Back Camera Position Setting" screen.

HINT:
·

The "Next" does not respond until the system memorizes the steering center and maximum steering wheel angle.

·

It is also possible to start by initially turning the steering to the right side.

·

When "MAX STEERING ANGLE MEMORIZE" is selected, a beep will sound to confirm that the adjustment values have been stored.

·

The adjustment values will not be stored unless "MAX STEERING ANGLE MEMORIZE" is selected after turning the steering wheel from lock to lock.

·

When "Back" is selected, the screen changes to the "Car Signal Check" screen without storing any values.

·

Even if no DTCs are detected, selecting "MAX STEERING ANGLE MEMORIZE" may not cause the adjustment values to be stored if the spiral with sensor cable sub-assembly is malfunctioning.

·

If selecting "MAX STEERING ANGLE MEMORIZE" does not cause the adjustment value to be stored after performing the steering angle setting procedure, replace the spiral with sensor cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).





d.
E286096E11
0.969,1.01 0.281,1.01 false 3.042,1.021 2.406,1.021 false 0.281,0.677 1.229,0.677 1.229,0.677 1.688,1.01 false 1.917,1.75 1.917,1.906 false 1.552,1.75 1.552,1.906 false 1.188,1.75 1.188,1.906 false 2.271,1.75 2.271,1.906 false 3.042,1.406 2.833,1.406 false 3.042,0.698 2.833,0.698 false 2.427,1.021 2.313,0.99 false 2.313,1.052 2.427,1.021 false 0.135,0.917 0.313,1.115 0.177,0.198 10 false A 3.073,0.938 3.25,1.135 0.177,0.198 10 false B 1.125,1.917 1.302,2.115 0.177,0.198 10 false C 1.854,1.917 2.031,2.115 0.177,0.198 10 false E 1.49,1.917 1.667,2.115 0.177,0.198 10 false D 3.073,0.615 3.25,0.813 0.177,0.198 10 false G 2.219,1.927 2.396,2.125 0.177,0.198 10 false F 3.073,1.333 3.25,1.531 0.177,0.198 10 false H 0.083,0.573 0.26,0.771 0.177,0.198 10 false *a

Back Camera Position Setting

Text in Illustration
*a Target Adjustment Bar for Back Camera Position Setting

HINT:
·

When adjusting the camera optical axis, "Back door is open. Do not use the rear view monitor when the back door is not completely closed." is displayed even after the back door has been closed.

·

When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and camera position setting will not be possible.

·

If the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "Back door is open. Do not use the rear view monitor when the back door is not completely closed." is displayed even after the back door has been closed) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>PROBLEM SYMPTOMS TABLE).



i.

Perform vertical and horizontal position adjustment.

·

Move the circle (A) left, right, up and down by selecting the buttons (C), (D), (E) and (F) so that the left end of Target Adjustment Bar for Back Camera Position Setting is positioned within the center of the circle (A) (center of the inner red circle).



ii.

Perform roll angle adjustment.

·

Rotate the bar (B) by selecting the buttons (G) or (H) so that the bar (B) becomes parallel to Target Adjustment Bar for Back Camera Position Setting.



iii.

Select "Next" on the "Back Camera Position Setting" screen.



e.

Back Verify Mode

i.
E286097E01
2.525,0.818 2.143,1.017 false 2.559,0.691 2.730,0.887 0.172,0.196 10 A

Check that (A) and the target adjustment bar are overlapping.

·

If the lines are not aligned, perform the "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" operations.

·

If (A) and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the back camera position setting operation.



ii.

Select "OK" to return to the "Function Check/ Setting I" screen and complete the adjustment.

HINT:
·

The update is not completed until "OK" is selected.

·

When "OK" is selected, a beep will sound to confirm that the adjustment values have been stored.

·

The adjustment values are not stored until the beep has sounded.






g.

Confirm steering angle adjustment.

HINT:

If the steering angle has been adjusted, confirm the steering angle adjustment on the parking assist monitor screen after finishing diagnostic mode.


i.

Check on the parking assist screen that the estimated course line moves until the steering wheel is fully turned to either the left or right.

HINT:

If the estimated course line stops moving before the steering wheel is fully turned to either the left or right, the steering angle adjustment values have not been stored correctly. In this case, perform "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" again.