Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261016 PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) T

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)  PROBLEM SYMPTOMS TABLE  


NOTICE:
·

The following inspection procedures for the parking assist monitor system are based on the assumption that the audio and visual system is normal. If the audio and visual system has any malfunctions, first proceed with troubleshooting the audio and visual system.

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>CALIBRATION).



HINT:
·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



Display
Symptom Suspected Area See page
Parking assist monitor display malfunction (distortion of the color/ screen) occurs continuously. Proceed to "Image from Camera for Parking Assist Monitor is Abnormal" (Click here)
Parking assist monitor display malfunction (distortion of the color/ screen) occurs temporarily. Check the usage conditions (explain to the customer that the display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver) -
When the shift lever is in R, an image of the area behind the vehicle is not displayed or displays for a while and then switches to another image. (screen is not black) Proceed to "Reverse Signal Circuit" (Click here)
Proceed to "Image from Camera for Parking Assist Monitor is Abnormal" (Click here)
Navigation receiver assembly (for Navigation Receiver Type) (Click here)
Radio and display receiver assembly (for Radio and Display Type) (Click here)
When the shift lever is in R, an image of the area behind the vehicle is not displayed. (screen is black) Proceed to "Black Screen" (Click here)
When the shift lever is not in R, an image of the area behind the vehicle is displayed. Proceed to "Reverse Signal Circuit" (Click here)
Proceed to "Image from Camera for Parking Assist Monitor is Abnormal" (Click here)
Navigation receiver assembly (for Navigation Receiver Type) (Click here)
Radio and display receiver assembly (for Radio and Display Type) (Click here)
When the shift lever is moved to R, the parking assist monitor is not displayed (navigation screen or multi-media screen remains displayed). Proceed to "Reverse Signal Circuit" (Click here)
Proceed to "Image from Camera for Parking Assist Monitor is Abnormal" (Click here)

Guide Line Malfunction
Symptom Suspected Area See page
The vehicle width extension guide lines and estimated course lines do not match when the steering wheel is turned to the center position. Check the installation of steering wheel (Click here)
Correct the steering angle neutral point (initialization) (Click here)
Steering angle setting (calibration) (Click here)
Check that the rear television camera assembly is correctly installed (w/ Tire Carrier) (Click here)
Check that the rear television camera assembly is correctly installed (w/o Tire Carrier) (Click here)
Back camera position setting (calibration) (Click here)
Rear television camera assembly (w/ Tire Carrier) (Click here)
Rear television camera assembly (w/o Tire Carrier) (Click here)
Spiral with sensor cable sub-assembly (Click here)

Parking Assist Monitor System Malfunction
Symptom Suspected Area See page
The estimated course lines are not displayed. Parking assist monitor screen display mode settings (check that estimated course line display mode is selected) -
Correct the steering angle neutral point (initialization) (Click here)
Steering angle setting (calibration) (Click here)
Rear television camera assembly (w/ Tire Carrier) (Click here)
Rear television camera assembly (w/o Tire Carrier) (Click here)
Navigation receiver assembly (for Navigation Receiver Type) (Click here)
Radio and display receiver assembly (for Radio and Display Type) (Click here)
Spiral with sensor cable sub-assembly (Click here)
Guide lines are not displayed for all parking assist monitor screen display modes. Check if the back door is not closed -
Steering angle setting (calibration) (Click here)
Back camera position setting (calibration) (Click here)
Rear television camera assembly (w/ Tire Carrier) (Click here)
Rear television camera assembly (w/o Tire Carrier) (Click here)
The guide lines are not displayed even though the back door is closed. Check that the back door light assembly illuminates normally (if not, refer to Lighting System (INT) - Problem Symptoms Table) (Click here)
Rear television camera assembly (w/ Tire Carrier) (Click here)
Rear television camera assembly (w/o Tire Carrier) (Click here)
The guide lines remain displayed even though the back door is open. Check that the back door light assembly illuminates normally (if not, refer to Lighting System (INT) - Problem Symptoms Table) (Click here)
Rear television camera assembly (w/ Tire Carrier) (Click here)
Rear television camera assembly (w/o Tire Carrier) (Click here)
The guide line switching screen is not displayed. Rear television camera assembly (w/ Tire Carrier) (Click here)
Rear television camera assembly (w/o Tire Carrier) (Click here)
Navigation receiver assembly (for Navigation Receiver Type) (Click here)
Radio and display receiver assembly (for Radio and Display Type) (Click here)
A guide line mode other than the one selected is displayed. CAN communication system (Click here)
Rear television camera assembly (w/ Tire Carrier) (Click here)
Rear television camera assembly (w/o Tire Carrier) (Click here)
Navigation receiver assembly (for Navigation Receiver Type) (Click here)
Radio and display receiver assembly (for Radio and Display Type) (Click here)
The button for the selected guide line mode does not change to the set color. A different button changes to the set color. CAN communication system (Click here)
Rear television camera assembly (w/ Tire Carrier) (Click here)
Rear television camera assembly (w/o Tire Carrier) (Click here)
Navigation receiver assembly (for Navigation Receiver Type) (Click here)
Radio and display receiver assembly (for Radio and Display Type) (Click here)
The display mode switch screen button cannot be pushed. CAN communication system (Click here)
Proceed to "Speed Signal Circuit" in Meter / Gauge System (Click here)
When adjusting the camera optical axis, "Back door is open. Do not use the rear view monitor when the back door is not completely closed." is displayed even after the back door has been closed. Check that the back door light assembly illuminates normally (if not, refer to Lighting System (INT) - Problem Symptoms Table) (Click here)
Rear television camera assembly (w/ Tire Carrier) (Click here)
Rear television camera assembly (w/o Tire Carrier) (Click here)
"Back Camera Guide Line Setting" screen is not displayed. Rear television camera assembly (w/ Tire Carrier) (Click here)
Rear television camera assembly (w/o Tire Carrier) (Click here)
Navigation receiver assembly (for Navigation Receiver Type) (Click here)
Radio and display receiver assembly (for Radio and Display Type) (Click here)
"CHK" message(s) are displayed on the signal check screen. Signal check (diagnosis system) (Click here)
When an image of the area behind the vehicle is displayed, the lines are misaligned. (the image from the camera is tilted) Back camera position setting (calibration) (Click here)