Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261016 PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the rear television camera assembly receives a signal via CAN communication from the spiral with sensor cable sub-assembly that indicates a power supply problem.

DTC Code DTC Detection Condition Trouble Area
C1625 Open or short in spiral with sensor cable sub-assembly power source
·

Harness or connector

·

Spiral with sensor cable sub-assembly



WIRING DIAGRAM

E224380E85
1.125,3.219 2.875,3.396 1.75,0.177 10 false : CAN Communication Line 3.229,0.604 3.583,0.781 0.354,0.177 10 false BAT 3.229,1.708 3.563,1.885 0.333,0.177 10 false ESS 5.063,2.198 7.104,2.417 2.042,0.219 10 false Navigation Receiver Assembly*1 2.031,1.344 3.042,1.521 1.01,0.177 10 false ECU-IG NO.1 2.271,0.813 2.802,1.01 0.531,0.198 10 false ECU-B 0.438,1.167 1.813,1.396 1.375,0.229 10 false from IG1 NO.1 Relay 0.927,0.625 1.844,0.823 0.917,0.198 10 false from Battery 2.969,2.344 4.51,2.76 1.542,0.417 10 false Spiral with Sensor Cable Sub-assembly 3.031,0.51 3.156,0.688 0.125,0.177 10 false 6 3.031,1.052 3.156,1.229 0.125,0.177 10 false 4 3.031,1.604 3.25,1.792 0.219,0.188 10 false 1 3.229,1.156 3.531,1.333 0.302,0.177 10 false IG 2.979,2.177 3.323,2.354 0.344,0.177 10 false G33 5.083,2.583 6.781,3 1.698,0.417 10 false Radio and Display Receiver Assembly*2 0.448,2.458 2.563,2.667 2.115,0.208 10 false *1: for Navigation Receiver Type 0.458,2.802 2.573,3.01 2.115,0.208 10 false *2: for Radio and Display Type

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When "System initializing" is displayed on the navigation receiver assembly*1 or radio and display receiver assembly*2 after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>INITIALIZATION).

*1: for Navigation Receiver Type

*2: for Radio and Display Type


·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>CALIBRATION).

·

The parking assist monitor system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the parking assist monitor system after confirming that the communication system is functioning properly (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
U149474E03
2.073,1.5 1.906,1.948 1.906,1.948 1.708,1.948 true 2.292,1.5 2.479,1.885 2.479,1.885 2.677,1.885 true 1.333,1.531 1.073,1.896 1.073,1.896 0.875,1.896 true 1.573,0.313 1.885,0.49 0.313,0.177 10 false G33 0.052,0.01 0.219,0.177 0.167,0.167 10 false *a 1.479,1.865 1.656,2.031 0.177,0.167 10 false IG 0.521,1.823 0.823,1.99 0.302,0.167 10 false ESS 2.688,1.813 2.99,1.979 0.302,0.167 10 false BAT

Disconnect the G33 spiral with sensor cable sub-assembly connector (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-2 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G33-5 (IG) - Body ground Engine switch on (IG) 11 to 14 V
G33-6 (BAT) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)


OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR