Home › Power Source / Network › 1KD-FTV (BATTERY / CHARGING) › CHARGING SYSTEM › 2015.06–2020.08
RM27T0E _57 Power Source / Network _053726 1KD-FTV BATTERY / CHARGING _0261024 CHARGING SYSTEM J

1KD-FTV BATTERY / CHARGING  CHARGING SYSTEM  Noise Occurs from V-ribbed Belt or Generator Assembly  


PROCEDURE

1.CONFIRM PROBLEM SYMPTOM
a.

Confirm the problem symptom.

Result:
Symptom Proceed to
Noise occurs from fan and generator V belt A
Noise occurs from generator assembly B




A

2.CHECK FAN AND GENERATOR V BELT FOR WEAR

B

6.CHECK FOR NOISE WHEN ROTOR IS TURNING FREELY
2.CHECK FAN AND GENERATOR V BELT FOR WEAR
a.

Check the fan and generator V belt for wear or damage.

OK:

The fan and generator V belt is not worn or damaged.




OK

3.CHECK GENERATOR PULLEY WITH CLUTCH FOR WEAR

NG

REPLACE FAN AND GENERATOR V BELT

3.CHECK GENERATOR PULLEY WITH CLUTCH FOR WEAR
a.

Check the generator with clutch pulley grooves for wear or damage.

OK:

The generator with clutch pulley grooves are not worn or damaged.




OK

4.CHECK FOR NOISE WHILE CLUTCH PULLEY IS OPERATING

NG

REPLACE GENERATOR WITH CLUTCH PULLEY

4.CHECK FOR NOISE WHILE CLUTCH PULLEY IS OPERATING
a.

Start the engine and check the generator with clutch pulley for looseness.

OK:

The generator with clutch pulley is not loose.




OK

5.INSPECT GENERATOR WITH CLUTCH PULLEY (UNIT INSPECTION)

NG

TIGHTEN GENERATOR WITH CLUTCH PULLEY TO SPECIFIED TORQUE

5.INSPECT GENERATOR WITH CLUTCH PULLEY (UNIT INSPECTION)
a.

b.

Check the installation condition of the generator pulley cap.

OK:

The generator pulley cap is not loose or missing.



c.

Check for grease leaks (for wet pulley) or particle formation due to friction (for dry pulley).

OK:

No grease leaks (for wet pulley) or large build-up of particles (for dry pulley).



d.

Check the generator with clutch pulley for misalignment (interference with the generator assembly).

OK:

The generator with clutch pulley is correctly aligned (no interference with the generator assembly).



e.
A288972

Turn the generator with clutch pulley clockwise and counterclockwise by hand and check for noise.

OK:

Noise does not occur when turned in both directions.



f.

Turn the generator with clutch pulley clockwise and counterclockwise by hand and visually check for runout.

OK:

The generator with clutch pulley does not have runout.



g.
A288971

Using a screwdriver, hold the fan of the generator rotor assembly located inside the generator assembly in place and check that the generator with clutch pulley locks when turned clockwise and turns freely when turned counterclockwise.

OK:

The generator with clutch pulley locks when turned clockwise and turns freely when turned counterclockwise.




OK

INSPECT PULLEY OTHER THAN GENERATOR ASSEMBLY PULLEY

NG

REPLACE GENERATOR WITH CLUTCH PULLEY

6.CHECK FOR NOISE WHEN ROTOR IS TURNING FREELY
a.

Perform a road test and check that noise does not occur when decelerating.

OK:

Noise does not occur.



b.

Turn the engine off and check that no noise is produced by the generator with clutch pulley as the engine stops.

OK:

Noise does not occur.




OK

7.CHECK ENGAGEMENT OF GENERATOR WITH CLUTCH PULLEY

NG

REPLACE GENERATOR WITH CLUTCH PULLEY

7.CHECK ENGAGEMENT OF GENERATOR WITH CLUTCH PULLEY
a.

b.
A288971

Using a screwdriver, hold the fan in the generator rotor assembly located inside the generator assembly in place and check that the generator with clutch pulley locks when turned clockwise (locking direction).

OK:

The generator pulley with clutch locks.




OK

REPAIR OR REPLACE GENERATOR ASSEMBLY

NG

REPLACE GENERATOR WITH CLUTCH PULLEY