Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261030 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU intermittently monitors the LIN communication bus between the components related to certification. DTC B2785 is stored when a malfunction in the LIN communication bus between the components related to certification is detected continuously 3 times.

DTC Code DTC Detection Condition Trouble Area
B2785 The certification ECU detects a malfunction in the LIN communication bus between components related to certification continuously 3 times.
·

Certification ECU

·

Power management control ECU

·

ID code box

·

Steering lock actuator assembly (steering lock ECU)

·

Harness or connector



WIRING DIAGRAM

C212389E04
4.298,0.929 4.604,1.101 0.306,0.172 10 G38 4.58,0.499 4.935,0.672 0.355,0.172 10 LIN 2.276,2.175 2.613,2.347 0.337,0.172 10 LIN1 2.299,0.499 2.616,0.672 0.317,0.172 10 LIN2 2.686,0.422 2.893,0.594 0.207,0.172 10 24 4.328,0.422 4.508,0.594 0.181,0.172 10 29 2.681,2.077 2.818,2.249 0.137,0.172 10 3 2.355,3.71 2.630,3.882 0.275,0.172 10 LIN 2.697,3.633 2.835,3.805 0.137,0.172 10 5 4.298,1.078 5.413,1.284 1.116,0.206 10 Certification ECU 1.591,0.955 2.759,1.128 1.167,0.172 10 G51 1.591,1.112 2.904,1.445 1.313,0.333 10 Power Management Control ECU 1.906,2.793 2.780,2.996 0.874,0.202 10 ID Code Box 1.906,2.644 2.796,2.816 0.890,0.172 10 G37 0.645,4.141 1.056,4.314 0.411,0.172 10 G35 0.645,4.291 4.119,4.460 3.473,0.169 10 Steering Lock Actuator Assembly (Steering Lock ECU)

CAUTION / NOTICE / HINT

NOTICE:

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.


HINT:

When DTC B2785 and B2287 are output simultaneously, perform troubleshooting for DTC B2785 first.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2785 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the G38 certification ECU connector.


b.

Disconnect the G51 power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G38-29 (LIN) - G51-24 (LIN2) Always Below 1 Ω
G38-29 (LIN) or G51-24 (LIN2) - Body ground Always 10 kΩ or higher




OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Connect the G38 certification ECU connector.


b.

Disconnect the G51 power management control ECU connector.




NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

6.CLEAR DTC

B

6.CLEAR DTC
a.

Connect the G51 power management control ECU connector.


b.

Disconnect the G35 steering lock actuator assembly (steering lock ECU) connector.




NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output (for Power Tilt and Power Telescopic Steering Column) B
DTC B2785 is not output (for Manual Tilt and Manual Telescopic Steering Column) C



A

8.CLEAR DTC

B

C

8.CLEAR DTC
a.

Connect the G35 steering lock actuator assembly (steering lock ECU) connector.


b.

Disconnect the G37 ID code box connector.




NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

REPLACE CERTIFICATION ECU

B

REPLACE ID CODE BOX