Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261030 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2287  LIN Communication Master Malfunction  B278C  Lost Communication with Power Source Control  


DESCRIPTION

·

DTC B2287 is stored when there is an open or short circuit or an ECU communication malfunction between the power management control ECU and certification ECU.

·

DTC B278C is stored when LIN communication between the certification ECU and power management control ECU stops for 10 seconds or more.


DTC Code DTC Detection Condition Trouble Area
B2287 There is an open or short circuit or an ECU communication malfunction between the power management control ECU and certification ECU.
·

Certification ECU

·

Power management control ECU

·

Harness or connector


B278C No communication between the certification ECU and power management control ECU for 10 seconds or more.
·

Certification ECU

·

Power management control ECU

·

Harness or connector



WIRING DIAGRAM

C212392E13
5.417,0.396 5.729,0.563 0.313,0.167 10 false LIN2 5.146,0.26 5.344,0.427 0.198,0.167 10 false 24 1.625,0.417 1.875,0.583 0.25,0.167 10 false LIN 1.969,0.281 2.167,0.448 0.198,0.167 10 false 29 5.417,0.74 5.823,0.906 0.406,0.167 10 false AM22 5.208,0.604 5.344,0.771 0.135,0.167 10 false 1 4.01,0.875 4.385,1.073 0.375,0.198 10 false AM2 2.448,0.708 3.26,0.969 0.813,0.26 10 false from Battery 5.417,1.031 5.813,1.198 0.396,0.167 10 false AM21 5.208,0.927 5.344,1.094 0.135,0.167 10 false 2 5.406,1.375 5.823,1.542 0.417,0.167 10 false GND2 5.208,1.24 5.344,1.406 0.135,0.167 10 false 5 5.417,1.708 5.813,1.875 0.396,0.167 10 false GND 5.208,1.552 5.344,1.719 0.135,0.167 10 false 6 4.927,2.083 5.219,2.25 0.292,0.167 10 false G51 4.927,2.25 6.99,2.458 2.063,0.208 10 false Power Management Control ECU 0.99,0.792 1.281,0.958 0.292,0.167 10 false G38 0.979,0.958 2.104,1.146 1.125,0.188 10 false Certification ECU

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC B2287 and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>B2785).


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2287 or B278C is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the G38 certification ECU connector.


b.

Disconnect the G51 power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G38-29 (LIN) - G51-24 (LIN2) Always Below 1 Ω
G38-29 (LIN) or G51-24 (LIN2) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY AND BODY GROUND)
a.
U169934E02
2.656,0.427 2.583,0.427 2.583,0.427 2.354,1.167 true 2.448,1.156 2.667,0.844 2.667,0.844 2.76,0.844 true 0.917,1.854 0.99,1.854 0.99,1.854 1.427,1.188 true 1.344,1.188 0.813,1.51 0.813,1.51 0.719,1.51 true 0.052,0.042 0.292,0.229 0.24,0.188 10 true *a 2.823,0.771 3.25,0.927 0.427,0.156 10 false AM22 0.365,1.438 0.708,1.594 0.344,0.156 10 false GND 0.49,1.781 0.917,1.969 0.427,0.188 10 false GND2 2.74,0.354 3.146,0.51 0.406,0.156 10 false AM21 2.813,1.281 3.146,1.438 0.333,0.156 10 false G51

Disconnect the G51 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G51-5 (GND2) - Body ground Always Below 1 Ω
G51-6 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G51-1 (AM22) - Body ground Always 11 to 14 V
G51-2 (AM21) - Body ground Always 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


OK

5.REPLACE POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Temporarily replace the power management control ECU with a new or normally functioning one (See page Power Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL).



NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2287 or B278C is not output.




OK

END (POWER MANAGEMENT CONTROL ECU IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU